manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, Руководство пользователя

Xilinx Virtex-5 FPGA ML561 - мощный продукт, предлагающий широкие возможности для пользователей. Для удобства пользования, предоставляется User Manual, который можно скачать бесплатно с manualshive.com. Пользователи могут найти подробные инструкции и руководства по использованию продукта для оптимальной производительности.

Поделиться
Скачать
background image

Virtex-5 FPGA User Guide

www.xilinx.com

63

UG190 (v5.0) June 19, 2009

DCM Design Guidelines

DCM Design Guidelines

This section provides a detailed description on using the Virtex-5 FPGA DCM and design 
guidelines. 

Clock Deskew

The Virtex-5 FPGA DCM offers a fully digital, dedicated, on-chip clock deskew. The 
deskew feature provides zero propagation delay between the source clock and output 
clock, low clock skew among output clock signals distributed throughout the device, and 
advanced clock domain control. 

The deskew feature also functions as a clock mirror of a board-level clock serving multiple 
devices. This is achieved by driving the CLK0 output off-chip to the board (and to other 
devices on the board) and then bringing the clock back in as a feedback clock. See the 

“Application Examples”

 section. Taking advantage of the deskew feature greatly 

simplifies and improves system-level design involving high-fanout, high-performance 
clocks.

Clock Deskew Operation

The deskew feature utilizes the DLL circuit in the DCM. In its simplest form, the DLL 
consists of a single variable delay line (containing individual small delay elements or 
buffers) and control logic. The incoming clock drives the delay line. The output of every 
delay element represents a version of the incoming clock (CLKIN) delayed at a different 
point. The clock distribution network routes the clock to all internal registers and to the 
clock feedback CLKFB pin. The control logic contains a phase detector and a delay-line 
selector. The phase detector compares the incoming clock signal (CLKIN) against a 
feedback input (CLKFB) and steers the delay-line selector, essentially adding delay to the 
DCM output until the CLKIN and CLKFB coincide, putting the two clocks 360° out-of-
phase, (thus, in phase). When the edges from the input clock line up with the edges from 
the feedback clock, the DCM achieves a lock. The two clocks have no discernible 
difference. Thus, the DCM output clock compensates for the delay in the clock distribution 
network, effectively removing the delay between the source clock and its loads. The size of 
each intrinsic delay element is a DCM_TAP (see the AC Characteristics table in the 

Virtex-5 

FPGA Data Sheet

). 

Figure 2-3

 illustrates a simplified DLL circuit.

To provide the correct clock deskew, the DCM depends on the dedicated routing and 
resources used at the clock source and feedback input. An additional delay element (see 

“Deskew Adjust”

) is available to compensate for the clock source or feedback path. The 

Xilinx ISE tools analyze the routing around the DCM to determine if a delay must be 
inserted to compensate for the clock source or feedback path. Thus, using dedicated 
routing is required to achieve predictable deskew.

X-Ref Target - Figure 2-3

Figure 2-3:

Simplified DLL Circuit

Clock

Distribution

Network

Variable

Delay Line

CLKOUT

Control

CLKFB

CLKIN

ug190_2_03_032506

Содержание Virtex-5 FPGA ML561


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex-5 FPGA ML561

Patton electronics 1090 Service Manual preview
1090
Бренд: Patton electronics Страницы: 8
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Бренд: Lattice Semiconductor Страницы: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Бренд: Lattice Semiconductor Страницы: 13
SeaLevel 7406e User Manual preview
7406e
Бренд: SeaLevel Страницы: 17
Fracarro FRPRO EVO HD Quick Start Manual preview
FRPRO EVO HD
Бренд: Fracarro Страницы: 12
Multitech MultiConnect SE MTS2EA Specification Sheet preview
MultiConnect SE MTS2EA
Бренд: Multitech Страницы: 2
IEI Technology HPE-6S2 Quick Installation Manual preview
HPE-6S2
Бренд: IEI Technology Страницы: 3
Eneo PNR-5304 Quick Installation Manual preview
PNR-5304
Бренд: Eneo Страницы: 68
axing EOC 1-31 Operation Instructions Manual preview
EOC 1-31
Бренд: axing Страницы: 52
Tandy 26-3814 Operation Manual preview
26-3814
Бренд: Tandy Страницы: 24
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Бренд: Infoblox Страницы: 13
Commell FS-A79 User Manual preview
FS-A79
Бренд: Commell Страницы: 36
AES BeBoPr++ User Manual preview
BeBoPr++
Бренд: AES Страницы: 44
Camozzi UVIX Use And Maintenance Manual preview
UVIX
Бренд: Camozzi Страницы: 22
Curtiss-Wright DTI-VME/S User Manual preview
DTI-VME/S
Бренд: Curtiss-Wright Страницы: 80
MSI CB11B Quick Start preview
CB11B
Бренд: MSI Страницы: 3
Lenze EPZ Series Mounting Instructions preview
EPZ Series
Бренд: Lenze Страницы: 29
Crestron DM-TX-200-C-2G Operations & Installation Manual preview
DM-TX-200-C-2G
Бренд: Crestron Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды