Xilinx Virtex-5 FPGA ML561 страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 385

background image

38

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 1:

Clock Resources

Clock Tree and Nets - GCLK

Virtex-5 clock trees are designed for low-skew and low-power operation. Any unused
branch is disconnected. The clock trees also manage the load/fanout when all the logic
resources are used.

All global clock lines and buffers are implemented differentially. This facilitates much
better duty cycles and common-mode noise rejection.

In the Virtex-5 architecture, the pin access of the global clock lines are not limited to the
logic resources clock pins. The global clock lines can access other pins in the CLBs without
using local interconnects. Applications requiring a very fast signal connection and large
load/fanout benefit from this architecture.

Clock Regions

Virtex-5 devices improve the clocking distribution by the use of clock regions. Each clock
region can have up to 10 global clock domains. These 10 global clocks can be driven by any
combination of the 32 global clock buffers. The dimensions of a clock region are fixed to
20 CLBs tall (40 IOBs) and spanning half of the die (

). By fixing the dimensions

of the clock region, larger Virtex-5 devices can have more clock regions. As a result,
Virtex-5 devices can support many more multiple clock domains than previous FPGA
architectures.

shows the number of clock regions in each Virtex-5 device. The

logic resources in the center column (CMTs, IOBs, etc.) are located in the left clock regions.

The CMTs, if used, utilize the global clocks in the left regions as feedback lines. Up to four
CMTs can be in a specific region. If used in the same region, IDELAYCTRL uses another
global clock in that region. See

Chapter 2, “Clock Management Technology.”

X-Ref Target - Figure 1-17

Figure 1-17:

Clock Regions

ug190_1_17_042406

All clock regions are 20 CLBs tall (10 CLBs above

and 10 CLBs below a horizontal clock line)

XC5VLX30 has 8 Clock Regions

XC5VLX330 has 24 Clock Regions

Center Column
Logic Resources

10 CLBs

10 CLBs

All clock regions

span half the die

«
...
36
37
38
39
40
...
»

Содержание Virtex-5 FPGA ML561


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex-5 FPGA ML561

Бренд: ebm-papst Страницы: 6

Бренд: ebm-papst Страницы: 6

Бренд: ebm-papst Страницы: 5

Бренд: NXP Semiconductors Страницы: 24

Бренд: Cypress Semiconductor Страницы: 11

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

Бренд: Z Microsystems Страницы: 51

Бренд: Abit Страницы: 22

Suzie-Q 541.35.520

Бренд: Hafele Страницы: 12

Бренд: Juniper Страницы: 420

DVI-Vision-IP-Fiber

Бренд: G&D Страницы: 240

Бренд: Teridian Страницы: 2

Бренд: DayTronic Страницы: 13

Бренд: Foxconn Страницы: 1

Threat Analysis Reporter TAR

Бренд: 8e6 Technologies Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды