Xilinx LogiCORE IP Скачать руководство пользователя страница 63

Страница: 63 / 142

XAUI v12.3 Product Guide

www.xilinx.com

PG053 April 6, 2016

Chapter 2:

Product Specification

Table 2-46

shows the PHY XS Status 1 register bit definitions.

MDIO Registers 4.2 and 4.3: PHY XS Device Identifier

Figure 2-31

shows the MDIO Registers 4.2 and 4.3: PHY XS Device Identifier.

Table 2

‐

46:

PHY XS Status 1 Register Bit Definitions

Bit

Name

Description

Attributes

Default
Value

4.1.15:8

Reserved

The block always returns 0s for these bits and

ignores writes.

R/O

All 0s

4.1.7

Local Fault

1 = Local fault detected
0 = No Local Fault detected
This bit is set to 1 whenever either of the bits

4.8.11, 4.8.10 are set to 1.

R/O

4.1.6:3

Reserved

The block always returns 0s for these bits and

ignores writes.

R/O

All 0s

4.1.2

PHY XS Receive

Link Status

1 = The PHY XS receive link is up.
0 =The PHY XS receive link is down.
This is a latching Low version of bit 4.24.12.

Latches 0 if Link Status goes down. Clears to

current Link Status on read.

R/O
Self-setting

4.1.1

Power Down

Ability

The block always returns 1 for this bit.

R/O

4.1.0

Reserved

The block always returns 0 for this bit and

ignores writes.

R/O

X-Ref Target - Figure 2-31

Figure 2

‐

31:

PHY XS Device Identifier Registers

DEVICE

IDENTIFIER

Reg 4.2

DEVICE

IDENTIFIER

Reg 4.3

X13703

Send Feedback

Содержание LogiCORE IP















































































































































Результаты поиска

Содержание LogiCORE IP

Отзывы:

Похожие инструкции для LogiCORE IP

Бренды по названию

Популярные бренды

Xilinx LogiCORE IP, Руководство по эксплуатации продукта

Результаты поиска

Содержание LogiCORE IP

Отзывы:

Похожие инструкции для LogiCORE IP

Бренды по названию

Популярные бренды