Xerox DocuPrint 3055 Скачать руководство пользователя | Manualshive

Страница: 222 / 240

background image

222

A Appendix

4.

Loosen the three screws that secure the
metal plate cover inside the printer.

5.

Pull the metal plate cover forward and
remove it from the printer.

6.

If an internal hard disk is installed, remove it
temporarily.
Use a screwdriver to remove the two
screws from the outside of the printer. Hold
the internal hard disk by the part shown in
the figure and pull it out upward.

7.

Align the notch on the font ROM with the
projection on the ROM slot and insert the
ROM at an angle into the slot.

Important

• The font ROM should be installed at the right of the

controller board. The slot at the left of the controller
board is for a memory card (optional). Make sure to
insert the font ROM into the correct slot.

8.

Push the font ROM as shown in the figure.
When the ROM is inserted correctly, it
clicks into place.

Note

• To remove the font ROM, push the retaining clips on

both ends in the outward directions and pull the ROM
out of the slot.

9.

If you removed an internal hard disk in a
previous step, re-install it into the controller
board.

«
...
220
221
222
223
224
...
»

Содержание DocuPrint 3055

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint 3055

Бренд: SPRT Страницы: 28

Бренд: Javelin Страницы: 2

EasyCoder 501 SA

Бренд: UBI Страницы: 214

Бренд: UBI Страницы: 64

Бренд: UltraTape Страницы: 52

Бренд: Ultimaker Страницы: 101

Бренд: Xerox Страницы: 2

imagePROGRAF GP-540

Бренд: Canon Страницы: 82

Бренд: Oki Страницы: 1

Бренд: Avery Dennison Страницы: 13

Бренд: Lanier Страницы: 234

DocuPrint C3300 DX

Бренд: Xerox Страницы: 200

1900N - B/W Laser Printer

Бренд: Kyocera Mita Страницы: 286

ESP Office 6100 Series

Бренд: Kodak Страницы: 94

Бренд: MIMAKI Страницы: 28

Бренд: VASTEX Страницы: 8

Бренд: Brady Страницы: 48

Бренд: Lanier Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды