Xerox DocuPrint 3055 Скачать руководство пользователя | Manualshive

Страница: 111 / 240

background image

5.2 Setting the Common Menus

111

[TCP/IP]

Set this when using the TCP/IP port.

Network / Port

TCP/IP

TCP/IP

Get IP Address

TCP/IP

IP Address

TCP/IP

Subnet Mask

TCP/IP

Gateway Address

Setting Item

Description

Get IP Address

Sets the method of obtaining the information (the IP address, subnet mask, or
gateway address) required to use the TCP/IP protocol.
• [DHCP/Autonet] (default)

Automatically obtains the information from the DHCP (Dynamic Host
Configuration Protocol) server that has the AutoIP feature.

• [Panel]

Sets the information manually on the control panel. Consult your network
administrator for the IP address number.

• [DHCP]

Automatically obtains the information from the DHCP server.

• [BOOTP]

Automatically obtains the information from the BOOTP.

• [RARP]

Automatically obtains the information from the RARP.

Note

• After changing this setting, reboot the printer.

IP Address,
Subnet Mask,
Gateway Address

Allows you to verify or manually enter the IP address.
Enter the IP address in the format of:
xxx.xxx.xxx.xxx
For IP or gateway addresses, xxx can be any number between 0 and 255.
However, the first xxx cannot be 127 or a number between 224 and 255.
For subnet masks, each xxx must be one of the following numbers:
0, 128, 192, 224, 240, 248, 252, 254, and 255. (See *2 on P. 132.)

Important

• Make sure you set the IP address correctly. Setting the wrong address can

cause problems on the network.

Note

• After changing this setting, reboot the printer.

«
...
109
110
111
112
113
...
»

Содержание DocuPrint 3055

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint 3055

Бренд: Nantian Electronics Страницы: 4

Бренд: Xerox Страницы: 9

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 150

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 6

Бренд: Xerox Страницы: 2

DocuPrint N2125

Бренд: Xerox Страницы: 246

DocuPrint N2025

Бренд: Xerox Страницы: 378

DocuPrint N2025

Бренд: Xerox Страницы: 176

DocuPrint C3290 FS

Бренд: Xerox Страницы: 240

Бренд: Xerox Страницы: 5

Бренд: Xerox Страницы: 7

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 10

Бренд: Xerox Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды