Xerox DocuPrint 3055 Скачать руководство пользователя | Manualshive

Страница: 141 / 240

background image

6.2 Hardware Problems (Power Failure, Abnormal Noise, etc.)

141

6.2

Hardware Problems
(Power Failure, Abnormal Noise, etc.)

Symptom

Cause/Remedy

The printer will not switch on.

Is the power switched on?
Switch the power on by pressing the power switch to the <|> position.

Is the power cord firmly plugged into the power outlet?
Switch the power off, plug the power cord firmly into the power connector or power
outlet, and switch the power back on.

Is the printer plugged into a power outlet that supplies proper voltage?
Connect the printer to a power outlet that supplies the proper rated voltage or current.
And do not share the power outlet with other devices.

The display is blank.

The printer may be in the Power Saver mode. Press the <Power Saver> button on the
control panel to exit the Power Saver mode.
If this does not remedy the problem, check if the power cord is firmly plugged into the
power outlet, and reboot the printer.
If the problem still persists, the printer may be at fault. Contact our Customer Support
Center or your dealers.

The printer makes odd noise.

Is the printer installed on a level surface?
Move the printer on a level and sturdy surface.

Are the paper trays pushed in completely?
Push the trays firmly into the printer.

A foreign object may be in the printer.
Switch the power off and remove the object. If the object cannot be removed without
dismantling the printer, contact our Customer Support Center or your dealers.

Dew condensation formed in
the printer.

On the control panel, set the interval that the printer switches to the Sleep mode to
more than 60 minutes, and let the printer stand with its power on. After about an hour,
the condensation disappears due to the heat inside the printer.

Refer to

• Sleep mode: [System Settings] (P. 116)

The printer does not switch to
the Sleep mode.

Isn't the Sleet mode disabled?
On the control panel, set [Sleep Mode] to [Enable].
The [Sleep Mode] setting is not supported on the model available in China.

«
...
139
140
141
142
143
...
»

Содержание DocuPrint 3055

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint 3055

Pixma MG2400 Series

Бренд: Canon Страницы: 2

Бренд: TASKalfa Страницы: 36

Бренд: Xerox Страницы: 44

Бренд: Oki Страницы: 76

Ecosys FS-C5300DN

Бренд: Kyocera Страницы: 35

Бренд: Citizen Страницы: 57

Бренд: Pantum Страницы: 164

DocumentCentre C240 Series

Бренд: Fuji Xerox Страницы: 275

Бренд: Domino Страницы: 114

Бренд: DataCard Страницы: 4

Бренд: Blocks Страницы: 9

Бренд: Ricoh Страницы: 542

PS121v2 - USB Mini Print Server

Бренд: NETGEAR Страницы: 50

Бренд: Markem Imaje Страницы: 13

Бренд: Jingda Страницы: 12

Бренд: Custom Engineering Страницы: 52

Бренд: MIMAKI Страницы: 130

Бренд: MIMAKI Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды