Xerox B205 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 206

background image

July 2019

4-3

Xerox® B205/B215 Multifunction Printer Service Manual

REP 1.1

Repairs / Adjustments

Initial Release

REP 1.1 Main PWB

Parts List on

PL 1.1

Removal

WARNING

Do not perform repair activities with the power on or electrical power supplied to the
machine. Some machine components contain dangerous electrical voltages that can
result in electrical shock and possible serious injury.

DANGER: Ne pas effectuer de dépannnage avec le contact principal activé ou avec l'ali-
mentation électrique appliquée à la machine. Certains éléments de la machine compor-
tent des tensions électriques dangereuses qui peuvent causer un choc électrique et de
graves blessures.

AVVERTENZA: Non effettuare alcuna riparazione con l'alimentazione elettrica inserita.
Alcuni componenti contengono corrente ad alta tensione che può provocare forti
scosse e gravi ferite.

VORSICHT: Es dürfen erst Reparaturarbeiten durchgeführt werden, wenn das Gerät aus-
geschaltet ist oder der Netzstecker nicht mehr mit der Stromquelle verbunden ist. Einige
Komponenten des Gerätes sind stromführend und können daher zu ernsthaften Verlet-
zungen oder Stromschlägen führen.

AVISO: No realice reparaciones con la máquina encendida o conectada a la corriente.
Algunos componentes de la máquina contienen voltajes eléctricos peligrosos que
pueden producir una descarga eléctrica y causar daños graves.

1.

Record the machine serial number from the Data Plate (located on the rear cover beneath
the bar code) or from a Configuration Report printed prior to installing the new PWB.
Refer to,

GP 2

, Machine Reports.

2.

Switch off the machine, then disconnect the power cord.

3.

Remove the Right Side Cover,

REP 2.2

.

4.

Remove the Wifi PWB,

REP 2.7

.

5.

Remove the Main PWB,

Figure 1

.

a.

Disconnect all the connectors on the Main PWB.

b.

Remove the screws (5) and the Main PWB.

Figure 1 Main PWB removal

Replacement

NOTE: Tapered plastic screws and round machine screws are used to hold the PWB to the
frame. Make sure that the plastic screws go into plastic components and machine screws go
into the metal frame.

The replacement is the reverse of the removal procedure.

After installing a new Main PWB, the following steps

MUST

be performed to write the machine

serial number to the new Main PWB:

1.

Reconnect the power cord, the switch on the machine.

2.

Set the serial number to the original machine number recorded in Step 1 of the Removal
procedure.

•

B215

a.

Enter Diagnostics,

GP 1

. Open

[Data Setup, Machine Data, Set Serial Num-

ber]

, then enter the original serial number from Step 1. Touch

[OK]

.

•

B205

a.

Enter Diagnostics

GP 1

. Using the up and down arrows, enter:

[Data Setup,

Machine Data, Set Serial Number]

, then enter the original serial number from

Step 1. Press the

[OK]

button.

3.

Perform

<Clear All Memory>

in Diagnostics:

[Data Setup, Machine Data, Clear All

Memory]

.

Main PWB

«
...
68
69
70
71
72
...
»

Содержание B205















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B205

Бренд: Xerox Страницы: 8

Бренд: F+D Feinwerk- und Drucktechnik Страницы: 22

Бренд: Lanier Страницы: 6

Бренд: Avery Dennison Страницы: 13

Бренд: Oce Страницы: 222

Бренд: Wang Страницы: 181

Бренд: Oki Страницы: 4

Бренд: Evolis Страницы: 45

Бренд: Tally Страницы: 14

Бренд: Xerox Страницы: 48

NanoPrint LM210

Бренд: Arrayit Страницы: 23

Бренд: Canon Страницы: 1154

Бренд: Develop Страницы: 176

Бренд: Detecto Страницы: 2

Бренд: Ricoh Страницы: 661

WorkCentre 4260/XF

Бренд: Xerox Страницы: 41

Бренд: Tally Dascom Страницы: 148

WORKCENTRE 5030

Бренд: Xerox Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды