Xerox B205 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 206

background image

July 2019

2-24

Xerox® B205/B215 Multifunction Printer Service Manual

15-400 , 15-410, 15-420

Initial Release

Status Indicator RAPs

15-400 LDAP Communication Failure RAP

BSD-ON:

BSD 1

Control Panel Fault Displayed

B205: NA

B215: LDAP Communication Error

The machine is unable to contact the LDAP server.

WARNING

Do not perform repair activities with the power on or electrical power supplied to the
machine. The machine could activate and cause serious personal injury when the power
is on or electrical power is supplied.

DANGER: Ne pas effectuer de dépannage avec le contact principal activé ou avec l'ali-
mentation électrique appliquée à la machine: celle-ci pourrait démarrer et causer de
graves blessures.

AVVERTENZA: Non effettuare alcuna riparazione con la macchina accesa o con l'ali-
mentazione elettrica inserita. La macchina potrebbe avviarsi all'improvviso e causare
gravi ferite.

VORSICHT: Es dürfen keine Reparaturarbeiten durchgeführt werden, solange das Gerät
eingeschalten oder mit der Stromquelle verbunden ist. Das Gerät kann u.U in den Aktiv-
Zustand übergehen und somit erhebliche körperliche Schäden verursachen.

AVISO: No realice reparaciones con la máquina encendida o conectada a la corriente.
La máquina podría activarse y ocasionar daños personales graves.

Procedure

Printers using ethernet connection:

The ethernet connection is good.

Y

N

Connect the printer to the ethernet port connection.
Verify the ethernet connection is active and network services; Internet and other network
services or devices are working.

Printers using WiFi: check the CN1 connector between the WiFi PWB,

PL 1.1 Item 10

, and the

Main PWB,

PL 1.1 Item 4

.

The connector is fully seated.

Y

N

•

Check for contamination or obstruction in the connector.

•

Disconnect, then reconnect the connector.

•

If the fault persist, install a new WiFi PWB,

PL 1.1 Item 10

.

Perform the following checks:
•

Check the LDAP IP address or Host Name.

•

Check the LDAP port is open and connected.

15-410, 15-420 LDAP Search Failure RAP

Control Panel Fault Displayed

15-410

LDAP server returned an error during transmission.

B205: NA

B215: LDAP Search Error

15-420

Displays when LDAP search timeout has execeeded parameter.

B205: NA

B215: LDAP Time Limit has been Exceeded

The LDAP server returned an error during transmission.

Initial Actions

•

Ensure that the LDAP server is enabled on the device and that maximum search results
have not been exceeded.

•

Check if the LDAP search has exceeded time limit parameters.

Procedure

Resubmit the job. If problem persists, contact Email administrator.

«
...
43
44
45
46
47
...
»

Содержание B205















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B205

image Prograf iPF785 Series

Бренд: Canon Страницы: 136

Бренд: GBC Страницы: 110

Pixma MG2400 Series

Бренд: Canon Страницы: 2

Бренд: Unisys Страницы: 255

Бренд: Xerox Страницы: 199

Бренд: Oki Страницы: 100

Бренд: Oki Страницы: 2

Бренд: Xerox Страницы: 316

Бренд: Xerox Страницы: 74

Бренд: Xerox Страницы: 306

Бренд: Xerox Страницы: 16

Бренд: Xerox Страницы: 4

Бренд: Oki Страницы: 38

Бренд: Oki Страницы: 38

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 36

Бренд: Canon Страницы: 2

PIXMA TR4500 Series

Бренд: Canon Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды