Xerox B205 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 206

background image

July 2019

2-12

Xerox® B205/B215 Multifunction Printer Service Manual

07-530

Initial Release

Status Indicator RAPs

07-530 Paper Feed - Manual Feed Slot RAP

BSD-ON:

BSD 1

Control Panel Fault Displayed

B205:

Jam in the Bypass

B215:

Jam in the Bypass Tray

The lead edge was not detected by the Paper Feed Sensor.

Initial Actions

Clear any jammed sheets. Refer to Section 11 in the Xerox® B215/B205 User Guide for
detailed instructions on clearing paper jams.

WARNING

Do not perform repair activities with the power on or electrical power supplied to the
machine. The machine could activate and cause serious personal injury when the power
is on or electrical power is supplied.

DANGER: Ne pas effectuer de dépannage avec le contact principal activé ou avec l'ali-
mentation électrique appliquée à la machine: celle-ci pourrait démarrer et causer de
graves blessures.

AVVERTENZA: Non effettuare alcuna riparazione con la macchina accesa o con l'ali-
mentazione elettrica inserita. La macchina potrebbe avviarsi all'improvviso e causare
gravi ferite.

VORSICHT: Es dürfen keine Reparaturarbeiten durchgeführt werden, solange das Gerät
eingeschalten oder mit der Stromquelle verbunden ist. Das Gerät kann u.U in den Aktiv-
Zustand übergehen und somit erhebliche körperliche Schäden verursachen.

AVISO: No realice reparaciones con la máquina encendida o conectada a la corriente.
La máquina podría activarse y ocasionar daños personales graves.

Procedure

Check the position of the jammed sheet.

The lead edge reached the Retard Roll.

Y

N

Enter Diagnostic Mode, GP 1,

[Machine Test, Diagnostics Mode, DC330 Component

Control, 102-Sensor, Feed Sens]

to block and clear the Feed Sensor.

The sensor sig-

nal changes.
Y

N

1.

Check for an open or short circuit.

2.

Install a new Paper Feed Sensor PWB,

PL 4.4 Item 20

.

In Diagnostics Mode, select:

[101-Clutch, Tray 1 Pick up (Feed)]

to engage the drive to

pick up paper from tray 1.

The clutch engages.

Y

N

1.

Check for an open or short circuit.

2.

Install a new Feed Clutch,

PL 4.1 Item 5

.

Perform SCP Final Actions.

Check the Paper Feed Sensor Actuator.

The actuator moves freely is and undamaged.

Y

N

Install a new Paper Feed Actuator,

PL 4.4 Item 18

.

Inspect the Paper Feed Sensor for damage.

The sensor is OK.

Y

N

1.

Check for an open or short circuit.

2.

Install a new Paper Feed Sensor PWB,

PL 4.4 Item 20

.

Check the circuit of the Paper Feed Sensor.

«
...
31
32
33
34
35
...
»

Содержание B205















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B205

4250 - WorkCentre - Copier

Бренд: Xerox Страницы: 210

4150 - WorkCentre B/W Laser

Бренд: Xerox Страницы: 4

4118P - WorkCentre B/W Laser

Бренд: Xerox Страницы: 16

3635MFP - Phaser B/W Laser

Бренд: Xerox Страницы: 10

3635MFP - Phaser B/W Laser

Бренд: Xerox Страницы: 42

3300MFP - Phaser B/W Laser

Бренд: Xerox Страницы: 148

3250D - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 12

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 12

Бренд: Xerox Страницы: 12

4250 - WorkCentre - Copier

Бренд: Xerox Страницы: 16

Бренд: Oki Страницы: 95

Бренд: Canon Страницы: 4

Бренд: Xerox Страницы: 150

Бренд: Lexmark Страницы: 289

Бренд: Xerox Страницы: 3

LaserPro StellarMark IFII Series

Бренд: GCC Technologies Страницы: 111

490ST - Document Centre B/W Laser Printer

Бренд: Xerox Страницы: 322

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды