Xerox B205 Скачать руководство пользователя страница 177

Страница: 177 / 206

July 2019

6-18

Xerox® B205/B215 Multifunction Printer Service Manual

GP 2, GP 3

Initial Release

General Procedures / Information

Procedure (B205)

From the Control Panel:

Press the <

Information

> button

Use the up/down arrows to scroll to

<Info Pages

>, then press the <

> button.

Scroll to <

Usage Counter

> then press the <

> button to print a Usage Counter report.

Enter Diagnostics Mode, select <

Diagnostics

> then press the <

> button

Use the up/down arrows to select <

Report

>, then press <OK>.

Use the up/down arrows to select <

Usage Counter

>, then press <

>, then <

> again

to print a Usage Counter report.

GP 3 Machine Firmware Version

Purpose

Use this procedure to check the firmware version of the machine.

Procedure (B215)

At the Home screen touch

[Device > About > General]

Figure 1

The Firmware Version is listed as

[Software Version]

on the screen.

Figure 1 General information screen entry

NOTE: The Firmware version is also printed in the Configuration Report under Device
Setup labeled, System Software Version. Refer to

GP 6

, Machine Reports.

Procedure (B205)

From the Control Panel:

Press the <

Information

> button.

Use the up/down arrows to scroll to

Info Pages

, then press the <

> button.

Use the up/down arrows to scroll to

Configuration

then press the <

> button to print a

configuration report.

See

[System Software Version]

under

<Device Setup>

heading.

or:

Enter Diagnostics Mode,

GP 1

Use the up/down arrows to select <

Report

> then press <

Use the up/down arrows to select the desired report to print, press <

>, then <

again to print the report.

The firmware version is listed under Device Setup > System.

Содержание B205














































































































































































































Результаты поиска

Содержание B205

Отзывы:

Похожие инструкции для B205

Бренды по названию

Популярные бренды

Xerox B205, Руководство по обслуживанию

Результаты поиска

Содержание B205

Отзывы:

Похожие инструкции для B205

Бренды по названию

Популярные бренды