Xerox B205 Скачать руководство пользователя страница 36

Страница: 36 / 206

July 2019

2-15

Xerox® B205/B215 Multifunction Printer Service Manual

08-600 , 08-700

Status Indicator RAPs

Initial Release

08-600 Paper Jam in Duplex Area RAP

BSD-ON:

BSD 1

Control Panel Fault Displayed

B205: Jam at duplex path

B215: Jam in the Device

The machine has detected a paper jam in the Duplex Area.

Initial Actions

Remove jammed sheets from duplex area. Refer to Section 11 in the Xerox® B215/B205 User
Guide for detailed instructions on clearing paper jams.

Ensure that the paper guide and machine settings are correct for the paper that is loaded in the
tray.

Procedure

Check the Exit Sensor Actuator.

The actuator moves freely.

Install a new Exit Sensor Actuator.

Enter Diagnostic Mode,

GP 1

[DC330, [102] Out-Bin Full Sensor]

to block and clear the Exit

Sensor.

The sensor is OK.

Check that there is no contamination present.

Check for an open or short circuit.

Install a new Exit Sensor,

PL 4.1 Item 24

Check the following parts for wear or damage and replace if needed:

•

Duplex Paper Guide,

PL 4.2 Item 6

•

Duplex Gate,

PL 2.1 Item 7

•

Duplex Gate Spring,

PL 2.1 Item 8

•

Exit Paper Guide,

PL 2.1 Item 6

Verify the Duplex Gate is seated correctly and moves freely without binding.

08-700 Output Bin Full Fault

BSD-ON:

BSD 1

Control Panel Fault Displayed

B205: Output Bin Full. Remove Paper

B215: Output Bin Full. Remove Paper

The Output Tray Full Sensor has detected that the Output Tray is full.

Initial Actions

Remove sheets from the Output Tray. (Maximum capacity is 150 sheets/ standard paper 8.5 x
11 in./ 80g/m2.)

Procedure

Enter Diagnostics Mode. Select:

[Machine Test, EDC Mode, DC330 Component Control,

102-Sensor, Out Bin Full]

to test the Out Bin Full Sensor.

The signal changes.

•

Check the sensor connector is fully seated.

•

Check for and remove any contamination present.

•

Check for an open or short circuit.

•

Install a new Output Tray Full Sensor,

PL 4.3 Item 1

Check the Bin Full Sensor Actuator,

PL 2.2 Item 7

, for binding or any debri causing the actuator

to respond intermittently or fail to actuate the Output Tray Full Sensor. Clean the Bin Full Sen-
sor Actuator and surrounding area to full operation.

Содержание B205














































































































































































































Результаты поиска

Содержание B205

Отзывы:

Похожие инструкции для B205

Бренды по названию

Популярные бренды

Xerox B205, Руководство по обслуживанию

Результаты поиска

Содержание B205

Отзывы:

Похожие инструкции для B205

Бренды по названию

Популярные бренды