manualshive.com logo in svg

Xerox B205, Руководство по обслуживанию

Бесплатное руководство по установке Saab B205 доступно для скачивания на нашем веб-сайте. Этот подробный руководство поможет вам правильно установить ваш продукт и настроить его. Просто загрузите его с manualshive.com и следуйте инструкциям. Сделайте вашу жизнь проще с помощью нашего руководства.

Поделиться
Скачать
background image

July 2019

2-3

Xerox® B205/B215 Multifunction Printer Service Manual

01-150 , 02-100, 200

Status Indicator RAPs

Initial Release

 

01-150 Front Door Open RAP

BSD-ON:

BSD 1

Control Panel Fault Displayed

B205: Door Open

B215: Device Front Door is Open

The front door is open or the Front Cover Latched Sensor is defective.

WARNING

Do not perform repair activities with the power on or electrical power supplied to the 
machine. The machine could activate and cause serious personal injury when the power 
is on or electrical power is supplied.

DANGER: Ne pas effectuer de dépannage avec le contact principal activé ou avec l'ali-
mentation électrique appliquée à la machine: celle-ci pourrait démarrer et causer de 
graves blessures.

AVVERTENZA: Non effettuare alcuna riparazione con la macchina accesa o con l'ali-
mentazione elettrica inserita. La macchina potrebbe avviarsi all'improvviso e causare 
gravi ferite.

VORSICHT: Es dürfen keine Reparaturarbeiten durchgeführt werden, solange das Gerät 
eingeschalten oder mit der Stromquelle verbunden ist. Das Gerät kann u.U in den Aktiv-
Zustand übergehen und somit erhebliche körperliche Schäden verursachen.

AVISO: No realice reparaciones con la máquina encendida o conectada a la corriente. 
La máquina podría activarse y ocasionar daños personales graves.

Procedure

Check the Front Door Open Switch operation on the HVPS PWB.  

The switch is good. 

Y

N

•

Check 

CN100

, FFC, is fully seated in the connector on the HVPS PWB and Main

Controller, 

CN12

.

•

Install a new HVPS PWB, 

PL 4.1 Item 2

.

Check the FFC connection between the Main PWB, 

CN12

 and the HVPS, 

CN100

.  

The con-

nection is secure.
Y

N

•

Check that there is no contamination present.

•

Check for broken or defective wires or cables.

•

Install a new Main PWB, 

PL 1.1 Item 4

.

Install a new Main PWB, 

PL 1.1 Item 4

.  

02-100, 200 USB Error RAP

BSD-ON:

BSD 1

Control Panel Fault Displayed

02-100

 Invalid/Unknown USB device.

B205: Invalid USB device

B215: Incompatible USB Device has been Detected

02-200

 Check USB memory.

B205: NA

B215: USB Memory is Full

WARNING

Do not perform repair activities with the power on or electrical power supplied to the 
machine. The machine could activate and cause serious personal injury when the power 
is on or electrical power is supplied.

DANGER: Ne pas effectuer de dépannage avec le contact principal activé ou avec l'ali-
mentation électrique appliquée à la machine: celle-ci pourrait démarrer et causer de 
graves blessures.

AVVERTENZA: Non effettuare alcuna riparazione con la macchina accesa o con l'ali-
mentazione elettrica inserita. La macchina potrebbe avviarsi all'improvviso e causare 
gravi ferite.

VORSICHT: Es dürfen keine Reparaturarbeiten durchgeführt werden, solange das Gerät 
eingeschalten oder mit der Stromquelle verbunden ist. Das Gerät kann u.U in den Aktiv-
Zustand übergehen und somit erhebliche körperliche Schäden verursachen.

AVISO: No realice reparaciones con la máquina encendida o conectada a la corriente. 
La máquina podría activarse y ocasionar daños personales graves.

Procedure

 Perform the steps that follow:

1.

Switch off, then switch on the machine.

2.

Ensure that the customer is using a valid USB device with sufficient free file space.

3.

Check the wiring between the USB host and the Main PWB, 

CN1

.

4.

If the fault persists, install a new Main PWB, 

PL 1.1 Item 4

.

NOTE: Be aware, the part number for the Main PWB-B215 and Main PWB-B205 are dif-
ferent.

Содержание B205















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B205

Oki C910 Hardware preview
C910
Бренд: Oki Страницы: 2
Oki C910 Material Safety Data Sheet preview
C910
Бренд: Oki Страницы: 52
Oki C110 Manual Do Usuário preview
C110
Бренд: Oki Страницы: 117
Oki C110 How To Remove Jammed Paper preview
C110
Бренд: Oki Страницы: 45
Oki C110 Manual De L'Utilisateur preview
C110
Бренд: Oki Страницы: 112
Oki C110 Guías Del Usuario Manual preview
C110
Бренд: Oki Страницы: 115
Oki C110 Quick Setup preview
C110
Бренд: Oki Страницы: 2
Oki ES7131 User Manual preview
ES7131
Бренд: Oki Страницы: 137
Panasonic Workio DP-C262 Scanner Manual preview
Workio DP-C262
Бренд: Panasonic Страницы: 54
Panasonic KXMB2000E Important Information Manual preview
KXMB2000E
Бренд: Panasonic Страницы: 12
Panasonic KX-MB2000 Important Information Manual preview
KX-MB2000
Бренд: Panasonic Страницы: 12
Panasonic KX-MB1500E Important Information Manual preview
KX-MB1500E
Бренд: Panasonic Страницы: 8
Panasonic KX-FLB851 - All-in-One Flatbed Laser Fax Guía De Referencia Rápida preview
KX-FLB851 - All-in-One Flatbed Laser Fax
Бренд: Panasonic Страницы: 28
Panasonic KX-FLB751 Information Manual preview
KX-FLB751
Бренд: Panasonic Страницы: 2
Panasonic DP-MB350 Quick Reference Manual preview
DP-MB350
Бренд: Panasonic Страницы: 12
Panasonic DP-MB300 Quick Reference Manual preview
DP-MB300
Бренд: Panasonic Страницы: 12
Xerox DC240 - DocuColor 240 Color Laser Quick Start Manual preview
DC240 - DocuColor 240 Color Laser
Бренд: Xerox Страницы: 2
Xante ColourLaser series guide Quick Reference Manual preview
ColourLaser series guide
Бренд: Xante Страницы: 31

Бренды по названию

Популярные бренды

Загрузить еще бренды