Xantrex Freedom SW 815-2024 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 96

background image

97-0019-01-01

15

Operating the Freedom SW with the SCP

This section contains detailed information and procedures for using your
Freedom SW in conjunction with the SCP.
If you’re using the SCP to operate or monitor the status of the unit, you may
also refer to the

Xanbus System Control Panel Owner’s Guide

.

The SCP provides operating, configuration, and monitoring capability for
your Xanbus system.
The System Control Panel:
•

Monitors activity throughout your onboard power system.

•

Displays the latest information about your inverter/charger, battery
voltage level, battery charge output, and generator start and stop
activity.

•

Displays the settings for each Xanbus-enabled device in the system.

•

Enables you to adjust the settings for each Xanbus-enabled device in
the system.

•

Preserves all of its settings if system power is interrupted. After power
is restored, you don’t have to reconfigure the SCP or any of the
Xanbus-enabled devices connected to it.

This section provides information on operating the Freedom SW with the
System Control Panel. Please refer to the System Control Panel Owner’s
Guide for complete information on using the System Control Panel.

LIMITATIONS ON USE

•

Do not use in connection with life support systems or other medical
equipment or devices.

•

Do not use in ambulances or other life-saving emergency vehicles.

Failure to follow these instructions can result in death or serious
injury.

Freedom SW 3K2K InvChg Owners Guide.book Page 15 Wednesday, October 9, 2013 1:34 PM

«
...
27
28
29
30
31
...
»

Содержание Freedom SW 815-2024

































































































Отзывы:

Нет отзывов

Похожие инструкции для Freedom SW 815-2024

Бренд: XS Scuba Страницы: 4

Бренд: Wacker Neuson Страницы: 22

Бренд: TTI Страницы: 7

Бренд: Grape Solar Страницы: 2

Бренд: KYLAND Technology Страницы: 12

Бренд: Lumantek Страницы: 14

VECTOPOWER VP600 Series

Бренд: Aradex Страницы: 114

Бренд: DAISHIN Страницы: 28

Бренд: argon audio Страницы: 6

Бренд: YOKOGAWA Страницы: 4

Бренд: Tektronix Страницы: 74

Бренд: Kostal Страницы: 12

Бренд: StarTech.com Страницы: 12

Бренд: Tripp Lite Страницы: 24

Бренд: Cross Technologies Страницы: 18

Бренд: Diehl Страницы: 28

Бренд: DigiTech Страницы: 4

Бренд: GoMax Electronics Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды