Xantrex Freedom SW 815-2024 Скачать руководство пользователя | Manualshive

Страница: 19 / 96

background image

97-0019-01-01

5

Introduction

Basic Protection Features

The Freedom SW has the following protection features:
•

over temperature shutdown for critical components such as the
transformer and the power board

•

battery temperature sensor (BTS) failure/battery temperature out-of-
range fault protection

•

DC output over voltage protection during charge mode,

•

AC transfer relay failure detection

•

AC output overload and short circuit protection during invert mode

•

AC backfeed

1

protection

•

short circuit protection for the BTS and communication connector
ports including protection from incorrectly inserting the remote panel
communication cable plug into the BTS port and vice versa

The Battery Temperature Sensor (BTS) provides these protection features:
•

battery over temperature charging protection preventing battery
charging at 60 °C (140 °F) or higher

•

charging voltage compensation based on the temperature of the battery
the BTS is connected to

1.An AC backfeed error occurs when the AC output of the inverter/charger is con-
nected or routed back to the inverter/charger’s AC input terminal or if the internal
transfer relay fails.

Freedom SW 3K2K InvChg Owners Guide.book Page 5 Wednesday, October 9, 2013 1:34 PM

«
...
17
18
19
20
21
...
»

Содержание Freedom SW 815-2024

































































































Отзывы:

Нет отзывов

Похожие инструкции для Freedom SW 815-2024

Бренд: Harmonic Страницы: 27

Бренд: Ikelite Страницы: 2

Бренд: PowerConnections Страницы: 10

Z3-SBE264-DVR-13

Бренд: Z3 Technology Страницы: 50

Бренд: CYP Страницы: 12

Бренд: Magtek Страницы: 54

Бренд: B&B Electronics Страницы: 2

Бренд: Fronius Страницы: 135

Бренд: Maplin Страницы: 3

Бренд: 3One data Страницы: 2

Бренд: Omnitracs Страницы: 9

Бренд: MPP Solar Страницы: 33

Бренд: JDS Labs Страницы: 5

Бренд: TSUNESS Страницы: 18

PP4000 AC PowerPack

Бренд: Lorentz Страницы: 2

Бренд: Trycom Technology Страницы: 28

Бренд: TECO Страницы: 93

Бренд: StarTech.com Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды