Xantrex Freedom SW 815-2024 Скачать руководство пользователя страница 40

Страница: 40 / 96

Freedom SW Owner’s Guide

Operating the Freedom SW with the SCP

Table 3

Device Setup Screen Status Information

Line 1

Label

: “

FSW3012 00: Setup

”

Line 2

Label

Mode

Field 1

: Freedom SW operating mode or “operating state”

(see Table 4 on page 27).

Line 3

Label

Battery

Field 2

: Total battery current. Negative value if the battery is

discharging and positive value when charging.

Field 3

: Battery voltage

Field 4

: Battery temperature. Displays the highest temperature when

reading multiple inverters that are installed. Displays

N/A

when

there is no BTS attached.

FSW3012 00: Setup

Mode
Battery
Load
AC In

Invert

11.9V -8.8A N/A

915W 120V 7A

0V 0A 60Hz

Line 1
Line 2
Line 3
Line 4
Line 5

Field 2

Field 1

Field 5

Field 3

Field 4

Field 6
Field 7

Field 8 Field 9 Field 10

Line 4

Label

Load

Field 5

: Total power drawn by AC loads connected to the unit.

Field 6

: Inverter output voltage at load terminals of one inverter/

charger unit.

Field 7

: Sum of all current drawn out by the AC loads.

Line 5

Label

AC In

Field 8

: AC input voltage at AC In terminals of the inverter/charger.

Field 9

: Sum of all current drawn into one inverter/charger unit.

Field 10

: AC input frequency

STBY/ON Fault Clear

button

Press momentarily to clear all faults on all devices on the network.
Press and hold for five seconds to switch all devices in the network
between operating and safe modes.

Enter

Up arrow

Down arrow

buttons

(pressed
simultaneously)

Switches between Basic Settings and Advanced Settings.

Table 3

Device Setup Screen Status Information

Freedom SW 3K2K InvChg Owners Guide.book Page 26 Wednesday, October 9, 2013 1:34 PM

Содержание Freedom SW 815-2024

































































































Результаты поиска

Содержание Freedom SW 815-2024

Отзывы:

Похожие инструкции для Freedom SW 815-2024

Бренды по названию

Популярные бренды

Xantrex Freedom SW 815-2024, Руководство пользователя

Результаты поиска

Содержание Freedom SW 815-2024

Отзывы:

Похожие инструкции для Freedom SW 815-2024

Бренды по названию

Популярные бренды