Winterthur Instruments AG CoatMaster Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 86

background image

Operation Manual CoatMaster

76/83

9.2

Malfuntions and their remedy

Error message

Corrective measure

No device found

Check the WLAN connection.   When the error
persits, shut-‐down   the PC   and   switch   the PC   and
the device off   and on again. Reestablish   the
WLAN connection.

Set configuration of USB DAQ failed

Shut-‐down the PC and switch the PC and the
device off and on again. Reestablish the WLAN
connection.

Flash generator error

Shut-‐down the PC and switch the PC and the
device off and on again. Reestablish the WLAN
connection.

Flash generator not found

Shut-‐down   the PC   and   switch   the PC   and   the
device off and   on   again. Reestablish   the WLAN
connection. When the error persists, please con-‐
tact   the manufacturer.

Data acquisition failed

Shut-‐down the PC and switch the PC and the
device off and on again. Reestablish the WLAN
connection.

Setting measure frequency failed

Shut-‐down the PC and switch the PC and the
device off and on again. Reestablish the WLAN
connection.

Trigger signal not found

Shut-‐down the PC and switch the PC and the
device off and on again. Reestablish the WLAN
connection.

Data storage failed

Please contact the manufacturer.

Measured head is too short

Shut-‐down the PC and switch the PC and the
device off and on again. Reestablish the WLAN
connection.

Optimization routine failed

Repeat the measurement.

Error in Jacobi matrix calculation

Repeat the measurement.

No results of optimization routine achieved

Repeat the measurement.

Signal too low

Increase the flash power or bring the sample
closer to the measurement window.

File loading failed

Shut-‐down   the PC   and   switch   the PC   and   the
device off and   on   again. Reestablish   the WLAN
connection. When the error persists, please con-‐
tact   the manufacturer.

«
...
75
76
77
78
79
...
»

Содержание CoatMaster























































































Отзывы:

Нет отзывов

Похожие инструкции для CoatMaster

Бренд: Campbell Страницы: 25

Бренд: Larson Davis Страницы: 2

Бренд: G-Tek Страницы: 27

Бренд: Kawai Страницы: 142

Бренд: Kawai Страницы: 10

Бренд: C-LOGIC Страницы: 4

Бренд: Felix Instruments Страницы: 102

Бренд: National Instruments Страницы: 38

Бренд: EUPRY Страницы: 6

Бренд: REED Страницы: 4

Бренд: Dewetron Страницы: 24

Бренд: Hilti Страницы: 31

Бренд: H-Star Страницы: 36

Бренд: SIGLENT Страницы: 32

Бренд: PCE Health and Fitness Страницы: 11

Бренд: Jaquet Страницы: 27

Бренд: Zhengzhou Minghe Electronic Technology Страницы: 7

Бренд: Vega Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды