Winmate FA33 Скачать руководство пользователя страница 46

Страница: 46 / 54

3 - 16

FA33 Mainboard Manual

MODEM Use IRQ

This feature allows you to select the IRQ# to meet your modems IRQ#.

The options are: 3, 4, 5, 7, 9, 10, 11.

Soft-Off by PWR-BTTN

The selection Delay 4 Sec. will allow the system shut down after 4 seconds

after the power button is pressed. The selection Instant-Off will allow the

system shut down immediately once the power button is pressed.

The settings are: Delay 4 Sec, Instant-Off.

VGA

enables the power management timers when a no activity events is

detected in the VGA.

OFF

disables the PM timer even if a no activity event

is detected. The options are: OFF, ON.

State After Power Failure

The item allows you to select the state that your personal computer re-

turns to after a power failure. If set at Off, the system will not boot after a

power failure. If set On, the system will restart after power failure.

The settings are: Auto, On, Off.

Video Off Method

The option

V/H SYNC+Blank

allows the BIOS to blank off screen display

by turning off the V-Sync and H-Sync signals sent from add-on VGA card.

DPMS Support

allows the BIOS to blank off screen display by your add-

on VGA card which supports DPMS (Display Power Management Signal-

ing function).

Blank Screen

allows the BIOS to blank off screen display by

turning off the red-green-blue signals.

The options are: V/H SYNC+Blank, DPMS Support, Blank Screen.

Video Off Option

This feature provides the selections of the video display power saving

mode. The option Suspend - Off allows the video display to go blank if the

system enters Suspend mode. The option All Modes - Off allows the video

display to go blank if the system enters Doze mode or Suspend mode. The

option Always On allows the video display to stay in Standby mode even

when the system enters Doze or Suspend mode.

The options are: Suspend - Off, All Modes -> Off, Always On.

Содержание FA33























































Результаты поиска

Содержание FA33

Отзывы:

Бренды по названию

Популярные бренды

Winmate FA33, Руководство пользователя

Результаты поиска

Содержание FA33

Отзывы:

Бренды по названию

Популярные бренды