manualshive.com logo in svg

Winmate FA33, Руководство пользователя

Поделиться
Скачать
Winmate FA33 Скачать руководство пользователя страница 42

3 - 12

FA33 Mainboard Manual

USB Keyboard Support

Set at Enabled when you use a USB keyboard; if not, set at Disabled.

The options are: Enabled, Disabled.

IDE HDD Block Mode

When enabled, the system executes read/write requests to hard disk in

block mode. The options are: Enabled, Disabled.

Onboard FDD Controller

When enabled, the floppy diskette drive (FDD) controller is activated.

The options are: Enabled, Disabled.

Onboard Serial Port 1

If the serial port 1 uses the onboard I/O controller, you can modify your

serial port parameters. If an I/O card needs to be installed, COM3 and

COM4 may be needed. The options are: 3F8/IRQ4, 3E8/IRQ4, 2F8/IRQ3,

2E8/IRQ3, Disabled.

Onboard Serial Port 2

If the serial port 2 uses the onboard I/O controller, you can modify your

serial port parameters. If an I/O card needs to be installed, COM3 and

COM4 may be needed. The options are: 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3,

3F8/IRQ4, Disabled.

IR Function Duplex

This feature is available only it  the above item , UART2 Mode, is set at

ASKIR or  HPSIR. It allows you to select the infrared data transaction way.

The options are: Half , Full.

TX,  RX Inverting Enable

This feature is available only it  the above item , UART2 Mode, is set at

ASKIR or  HPSIR. It allows you to  select the active signals of  the recep-

tion end and  the transmission end.

The options are: No, Yes; Yes, Yes;  No, No; Yes, No.

Содержание FA33























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды