background image

088-00

2

60706-207

SAVE THESE INSTRUCTIONS

This manual contains important instructions that 

should be followed during installation and main-

tenance of the generator and batteries.  Read 

and understand all instructions in the manual 

before starting and operating the generator set.

USING THE MANUAL

Congratulations on your choice of a Winco genera-

tor set.  You have selected a high-quality, precision 

engineered generator set designed and tested to 

give you years of satisfactory service.   

 

To get the best performance from your new engine 

generator set, it is important that you carefully read 

and follow the operating instructions in this manual.

 

 

 

 

 

 

Should you experience a problem please follow 

the “Troubleshooting Tables” near the end of this 

manual.  The warranty listed in the manual describes 

what you can expect from WINCO should you need 

service assistance in the future.   

 

 

 

TABLE OF CONTENTS

INTRODUCTION 

 

 

 

2

GUIDE TO PRODUCT SAFETY  

 

3

BASIC INFORMATION

 

Description 

 

 

 

4

 

Specifications   

 

 

5

PREPARING THE UNIT  

 

 

 

Unpacking the Unit 

 

 

5

ENGINE GENERATOR INSTALLATION   

 

Installation 

 

 

 

5

 

Fuel Installation  

 

          6,7

 

Vapor Fuel Pressure Tables 

 

8

 

Fuel Conversions 

 

 

8

 

Battery Installation 

 

 

9

 

Connecting Battery Charger 

 

TRANSFER SWITCH INSTALLATION

 

AC Electrical Connections 

        ,2

 

DC Electrical Connections 

 

3

INITIAL START UP 

 

 

   3,5,6

DSE 30 ENGINE CONTROL   

 

4

ASCO 85 SEQUENCE OF OPERATION 

8

FRONT PANEL CONFIGURATION 

 

9

DSE 30 FAULT CODES 

 

 

20

MAINTENANCE 

 

 

 

2

GENERATOR SET OUTLINE   

 

22

GENERATOR SET PAD LAYOUT 

 

23

TROUBLESHOOTING TABLES  

 

24

AC & DC SCHEMATICS  

 

 

25

MAINTENANCE LOG   

 

        26,27

2 MONTH WARRANTY 

 

 

28

PROPER USE AND

INSTALLATION

You must be sure your new engine generator set is:

 

* Properly serviced before starting.

 

* Operated in a well ventilated area.

 

* Properly exhausted and gases safely   

 

   dispersed.

 

* Wired by a qualified electrician.

 

* Operated only for its designed purposes.

 

* Used only by operators who understand

 

  its operation.

 

* Properly maintained.

COPY YOUR MODEL AND 

SERIAL NUMBER HERE

No other WINCO generator has the same serial 

number as yours.  It is important that you record 

the number and other vital information here.  If you 

should ever need to contact us on this unit it will help 

us to respond to your needs faster.

MODEL_

_________________________________

SERIAL NUMBER_________________________

PURCHASE DATE_________________________

DEALER_________________________________

DEALER PHONE # ________________________

Содержание ULPSS15B2E





























Отзывы: