Wilmod ELOTECH R4000 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 46

background image

Manual: R4000-XX-X-000-X-X_EN

Release: 1.20

©Elotech GmbH

Seite 44 / 48

6

Error Messages

Error message

Cause

Possible remedy

At actual process value
maximum value flashes

Top range end has
been exceeded, sen-
sor defect

Check sensor and cable

At actual process value
minimum value flashes

Bottom range end
has been exceeded,
sensor defect

Check sensor cable
Check process value offset
TC connected with inverted polarity

REMOTE:
Parameter
locked

Adjusting of parame-
ters is not allowed.
Device is controlled
by fieldbus.

Profibus: The parameter “Remote“ in the
menu Field bus is set to “on”.

EloVision is active!

Adjusting of parame-
ters is not allowed.
Device is controlled
by EloVision.

The configuration-tool EloVision is active.
Please close EloVision, or switch to the visu-
alisation page of von EloVision.

Field bus module
unavailable

The controller is not fitted with the correct
hardware for the selected protocol.

Zone synopsis:
Current: --.-A

No current measure-
ment

Set the logic output of the corresponding
zone to heating.

DfErr

Text display error

Please send the controller back to the
manufacturer.

ERR0

System error

Please send the controller back to the
manufacturer.

ERR8

System error

Quit error message.
Check the parameters. If the error is still
there, send the controller back to the
manufacturer.

ERR IO

Error I/O board
See logbook:
Error IO board 1 or 2

Error IO board 3 or 4

The connection to the input/output circuit
board is broken.
-> Internal card defective, please send the
controller back to the manufacturer.
-> If zone extension (5.4.9.2 menu About)
is set to 12 or 16, the required additional
module R4010 may not be connected.
Switch off zone extension if necessary.

Info: All 4 sensors of the faulty card are set
to sensor break.

«
...
42
43
44
45
46
»

Содержание ELOTECH R4000















































Отзывы:

Нет отзывов

Похожие инструкции для ELOTECH R4000

Бренд: Taie Страницы: 66

Бренд: Galcon Страницы: 32

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: UCS Страницы: 4

Бренд: GameSir Страницы: 8

Бренд: Tactical Страницы: 8

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: Vega Страницы: 20

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: HAOZEE Страницы: 16

Бренд: Vexve Страницы: 24

Бренд: Vector Страницы: 10

Бренд: TAC Vista Страницы: 2

Бренд: Ellard Страницы: 21

Бренд: Maintronic Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды