Whirlpool APARTMENT MAINTENANCE SERIES Скачать руководство пользователя

Страница: 58 / 132

Agitator Replacement

Refer to Figure 13 for these procedures.

1. Open the lid of the washer.

2. Loosen the hex head screw in the agitator access
hole. DO NOT REMOVE THIS SCREW.

3. Pull the agitator off the splined agitator shaft.

4. Position the new agitator over the splined
agitator shaft and turn it until the splines mate prop-
erly and press down on the agitator until it slides
down the shaft as far as it can go.

5. Retighten the hex head screw securely. Do not
overtighten it or the threads will strip.

Fig. 13

Basket Removal

Refer to Figures 14 and 15 for these procedures.

1. Remove the agitator.

2. Remove the top assembly.

3. Unsnap eight snap clips holding the tub ring to the tub and set the tub ring aside.

4. Loosen the drive hub screw by four or five turns. DO NOT REMOVE THIS SCREW.

5. Tap on the head of the drive hub screw to loosen the saddle block.

6. Pull up on the basket and remove it from the tub.

Fig. 14

Fig. 15

AGITATOR

HEX-HEAD SCREW

Содержание APARTMENT MAINTENANCE SERIES





































































































































Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Похожие инструкции для APARTMENT MAINTENANCE SERIES

Бренды по названию

Популярные бренды

Whirlpool APARTMENT MAINTENANCE SERIES, Руководство по обслуживанию

Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Похожие инструкции для APARTMENT MAINTENANCE SERIES

Бренды по названию

Популярные бренды