Whirlpool APARTMENT MAINTENANCE SERIES Скачать руководство пользователя страница 81

Страница: 81 / 132

Section Three - Part B

COMPONENT ACCESS

Removing the Console

Remove the two screws at the base of the console.

(Fig. 3-5)

Grab console on both sides. Pull console towards you, lifting the tabs up and out of the
console slots. Carefully flip console forward and remove the rear panel to make repairs.

Fig. 3-5

Fig. 3-6

WARNING

ELECTRIC SHOCK HAZARD

Disconnect the electrical power before servicing any components.

Failure to do so can result in death or electrical shock.

Removing the Timer

Pull the timer knob off the timer assembly shaft.

Tip the console into the service position.

Disconnect the wiring harness connectors from the timer assembly terminals.

Remove the two (2) screws securing the timer assembly mounting bracket to the console.

Removing the Clean Touch Switch Assembly

Tip the console into the service position.

Disconnect the wiring harness leads from the
terminals on the switch assembly.

Press in on the snap tabs as indicated in Fig. 3-7
and then pull the bottom of the switch assembly
out from the console.

Slide the top of the switch assembly down until the
ears clear the console and remove the switch
assembly.

Mounting “EARS”

Snap Tabs

PUSH IN

Fig. 3-7

Содержание APARTMENT MAINTENANCE SERIES





































































































































Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Бренды по названию

Популярные бренды

Whirlpool APARTMENT MAINTENANCE SERIES, Руководство по обслуживанию

Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Бренды по названию

Популярные бренды