Whirlpool APARTMENT MAINTENANCE SERIES страница 115 Скачать руководство пользователя

Страница: 115 / 132

107

Section Five - Part B

COMPONENT ACCESS

24” ThinTwin

Accessing the Control Panel

The control panel can be tilted down to the service position.

Loosen, but do not remove the two screws located on the bottom edge of the control panel.
This will release the console panel latching mechanism.

(Fig. 5-3)

With the control panel latches released, rotate the top of the control panel down.

Screws

Fig. 5-4

Fig. 5-3

Accessing the Washer Components

To gain access to the washer components, the transition panel and washer top must be removed first.

Remove the two screws securing the
transition panel to the unit.

(Fig. 5-5)

Tilt the transition panel down and pull it
straight out.

(Fig. 5-6)

Screws

Fig. 5-5

Fig. 5-6

Electrical Shock Hazard

Disconnect electric power from appliance before servicing.

Replace all panels before operating.

Failure to do so could result in death or electrical shock.

WARNING

Transition Panel

Control Panel

Содержание APARTMENT MAINTENANCE SERIES





































































































































Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Похожие инструкции для APARTMENT MAINTENANCE SERIES

Бренды по названию

Популярные бренды

Whirlpool APARTMENT MAINTENANCE SERIES, Руководство по обслуживанию

Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Похожие инструкции для APARTMENT MAINTENANCE SERIES

Бренды по названию

Популярные бренды