manualshive.com logo in svg

Whirlpool APARTMENT MAINTENANCE SERIES, Руководство по обслуживанию

Поделиться
Скачать
Whirlpool APARTMENT MAINTENANCE SERIES Скачать руководство пользователя страница 70

62

Table 8

TEMP SELECT

POSITION

WATER LEVEL

SWITCH

ACTION

Pump and Brake Solenoid

Agitate Function

Water Inlet System & Water Level Switch

Spin Function

HC

WC

CC

WW*

(This setting only
on 4-temperature

models)

n/a

Pump & Solenoid

Actuate

Dry Agitate

Empty

Full

Warm Fill

Agitate

Pump & Brake

Solenoid

Actuate, Spin

Empty

Full

Pump & Brake

Solenoid

Actuate

n/a

To terminate this test and return to normal operation, unplug the washer power cord from the power
outlet for more than five seconds and then plug the power cord back into the outlet.

To terminate this test and return to normal operation, unplug the washer power cord from the power
outlet for more than five seconds and then plug the power cord back into the outlet.

Table 9

STEP

3 SECOND OPERATIONS

Wash Cycle/Status LED on

Rinse Cycle/Status LED on

Spin Cycle/Status LED on

Cold Water Valve

Hot Water Valve

Motor Lead - Yellow

Motor Lead - Red

Pump and Solenoid

All OFF

Return to Step 1

1

2

3

4

5

6

7

8

9

10

Automatic Operations Test  (Set TEMP SELECT: Cold/Cold - Initiate Entry Sequence)

The Automatic Operations Test checks LEDs, Valves, Solenoid, Pump and both Drive Motor Windings
by turning each component on for approximately three seconds.

Actuator and Switch Test  (Set TEMP SELECT: Hot/Cold - Initiate Entry Sequence)
(Preferred Service Test)

The Actuator and Switch Test is designed to detect malfunctions in the transmission, water inlet
valves, pump, solenoid and clutch, and the lid switch.  Each function is tested separately by turning the
TEMPERATURE SELECT switch as indicated in 

Table 8.  Press the START/PAUSE button to start

and end each test.

Opening and closing the lid during any of the these tests will verify the lid switch.

NOTE:  CYCLE SELECT setting has no effect on the Actuator and Switch Test.

Содержание APARTMENT MAINTENANCE SERIES





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды