Whirlpool APARTMENT MAINTENANCE SERIES Скачать руководство пользователя страница 56

Страница: 56 / 132

Water Level Switch Removal

Refer to Figure 10 for these procedures.

1. Remove washer top.

2. Remove the three control pan screws. Turn the control pan over and lay it to one side.

3. Pull the upper water level tube from the nipple on the water level switch. Do not disconnect the

tube from the pan nipple.

4. Pull the connectors from the terminals on the water level switch.

5. Remove the water level switch mounting screw. This will free the ground connector and the

water level switch.

Water Level Switch Replacement

Refer to Figure 10 for these procedures.

1. Slide the water level switch mounting bracket tab into the mounting slot.

2. Install the mounting screw through the ground connector and the water level switch

bracket.

3. Route the three water level switch wires around the circuit board mounting post.

4. Push the upper water level switch tube onto the nipple on the water level switch.

5. Install the three control pan screws.

6. Install the washer top.

Fig. 11

Содержание APARTMENT MAINTENANCE SERIES





































































































































Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Бренды по названию

Популярные бренды

Whirlpool APARTMENT MAINTENANCE SERIES, Руководство по обслуживанию

Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Бренды по названию

Популярные бренды