Whirlpool APARTMENT MAINTENANCE SERIES Скачать руководство пользователя

Страница: 26 / 132

Removing the Water Level Switch

1. Pull the knob off of the switch shaft.
2. Unplug the wiring harness connector from

the switch assembly terminals and remove
pressure switch tubing.

3. Remove the Hex-head screw securing the

water level switch mounting bracket to the
console mounting plate

(Fig. 3-7-A) OR

depress tab and rotate the switch 90°and
pull it from the console mounting plate.
(Fig. 3-7-B)

Removing the Push-Button Assembly

1. Unplug the wiring harness connectors from the switch assembly terminals using a pair of

needlenose pliers.

2. Press in the the two (2) tabs at the bottom of the switch assembly. Then, lift the bottom of the

switch assembly up and lift it away from the console mounting plate.

(Fig. 3-6)

PUSH

TIP UP

and

LIFT OUT

MOUNTING

BRACKET

MOUNTING

HOLES

Fig. 3-6

Fig. 3-7-A

Metal Body

1. To remove the timer knob, push the knob

in from the front and unscrew it from the
timer shaft.

(Fig. 3-5)

2. Slide the timer dial from the timer hub.
3. Remove the two (2) Hex-head screws

securing the timer assembly to the console
mounting plate.

4. Unplug the wiring harness connector from

the timer assembly terminals.

Fig. 3-5

Fig. 3-7-B

ROTATE 90°

TO REMOVE

DEPRESS

TAB

Содержание APARTMENT MAINTENANCE SERIES





































































































































Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Похожие инструкции для APARTMENT MAINTENANCE SERIES

Бренды по названию

Популярные бренды

Whirlpool APARTMENT MAINTENANCE SERIES, Руководство по обслуживанию

Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Похожие инструкции для APARTMENT MAINTENANCE SERIES

Бренды по названию

Популярные бренды