Whirlpool APARTMENT MAINTENANCE SERIES Скачать руководство пользователя страница 62

Страница: 62 / 132

1. Follow the procedures for removing
the splutch assembly.

2. Follow the procedures for disconnecting
the brake arm assembly from the solenoid.

3. Squeeze the tabs on the four wiring harness
standoffs in the motor plate together
and push them out of their mounting
holes.

4. Cut the nylon cable tie that holds the wiring
harness connector to the motor plate.

5. Bend back the end clips slightly and separate the
motor plug from the wiring harness connector.

6. Remove the four hex head bolts securing the motor plate to the tub support.

7. Pull the motor plate assembly off the tub support.

1. Disconnect the water and drain hoses from
the washer.

2. Lay the washer on its front on a soft surface to
protect the cabinet finish.

3. Remove the nuts securing the plastic
motor pulley shield and remove the shield.

4. Remove the C-ring securing the splutch pulley to the
splutch assembly and remove the cup washer.

5. Pull the splutch pulley off the splined gearcase shaft
and then remove the pulley and the drive belt.

6. The splutch housing is held to the motor plate by four tabs. Work each tab loose by pressing in
while pulling out on the housing until it is free.

Splutch Assembly Removal

Refer to Figure 22 for these procedures.

Splutch Pulley

Motor Plate Removal

Refer to Figure 23 for these procedures.

Motor Plate

Bolts

Fig. 23

Fig. 22

Содержание APARTMENT MAINTENANCE SERIES





































































































































Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Бренды по названию

Популярные бренды

Whirlpool APARTMENT MAINTENANCE SERIES, Руководство по обслуживанию

Результаты поиска

Содержание APARTMENT MAINTENANCE SERIES

Отзывы:

Бренды по названию

Популярные бренды