Whirlpool APARTMENT MAINTENANCE SERIES страница 34 Скачать руководство пользователя | Manualshive

Страница: 34 / 132

background image

26

Agitator dogs worn
Excessive clearance on pinion
thrust or main drive gear

Shift actuator or cam damaged

Clogged drain
Pump
Drain hose kinked

Lid open
Lid switch defective
Lid switch disconnect plug open
Wiring harness
Timer switches
Motor
Cam driver broken
Weak clutch spring
Spin tube
Clothes between basket and tub
Worn Clutch Lining

Water inlet valve
Water temp. switch (if used)
Timer switches
Wiring harness

Not level
Front leveling leg locknuts not
tight
Weak floor
Unbalanced load
Shipping pins not removed
Rear leveling legs stuck
Rear Cabinet sides loose

Suspension plate sticky
Suspension plate damaged or
worn
Suspension pads damaged or
worn
Tub support friction area sticky
Tub support damaged or worn
Suspension springs missing
broken or not connected
Basket ballast missing
Base bent/out of square

7. KNOCK DURING
AGITATE.

8. TRIES TO AGITATE
DURING SPIN.

9. WATER DOES NOT
DRAIN FROM
MACHINE.

10. SLOW OR NO
SPIN.

11. MACHINE WILL
NOT SPRAY
RINSE.

12. EXCESSIVE
VIBRATION OR
MACHINE WALKS.

PROBLEM

POSSIBLE CAUSE

ACTION

Replace agitator dogs
Replace gearcase

Replace gearcase

Remove obstruction
Replace pump
Relocate hose to prevent kink

Close lid
Check continuity
Check plug engagement
Check continuity
Check continuity
See problem 1
Replace driver
Replace spring
Check bearings and replace
Remove
Replace clutch

Check voltage
Check continuity
Check continuity
Check continuity

Level
Secure locknut against frame after
leveling
Advise customer
Redistribute load
Remove pins
Loosen
Remove top clips, push cabinet sides
inward when reinstalling top clips
Replace plate
Replace plate

Replace pads

Replace tub support
Replace tub support
Replace or reconnect springs

Replace basket balance ring
Replace base

NOTE:

In diagnosing this

problem, start the washer in
spin and see if the clutch
drum spins. If it spins, the
problem is

not inside the

gearcase. If the clutch drum
does not spin, all or some of
the problem is inside the
gearcase.

«
...
32
33
34
35
36
...
»

Содержание APARTMENT MAINTENANCE SERIES





































































































































Отзывы:

Нет отзывов

Похожие инструкции для APARTMENT MAINTENANCE SERIES

Бренд: Maytag Страницы: 24

Бренд: Kärcher Страницы: 156

Бренд: Kärcher Страницы: 20

Бренд: Kärcher Страницы: 320

Бренд: Kärcher Страницы: 254

Cuda 4860 Series

Бренд: Kärcher Страницы: 56

Бренд: Hotpoint Страницы: 56

Бренд: Matsui Страницы: 8

Бренд: Cookology Страницы: 24

Computer Control 1100 A3268

Бренд: Hoover Страницы: 12

Бренд: ETNA Страницы: 100

Бренд: N'DUSTRIO Страницы: 27

Бренд: Asko Страницы: 16

Бренд: ZANKER Страницы: 28

Бренд: R+M Suttner Страницы: 8

Бренд: Blomberg Страницы: 40

Hydra-Clean 1020E Instructions-

Бренд: Graco Страницы: 14

Бренд: Fagor Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды