Whirlpool APARTMENT MAINTENANCE SERIES Скачать руководство пользователя | Manualshive

Страница: 69 / 132

background image

61

DIAGNOSTIC TEST PROGRAM

The Diagnostic Test Program is designed to be an aid for authorized service technicians to objectively
test the washer’s water fill valves, drain pump and the clutch/brake solenoid, drive motor, water level
sensor, lid switch, LEDs and rotary switches. There are four tests in the program all accessed from
the control panel by following a specified entry sequence. NOTE: Check the Tech Sheet provided
with the washer for most recent test sequences.

Entry Sequence

The entry sequence to begin the Diagnostic Test Program is as follows:

1.

Set the TEMP SELECT switch for the desired test according to the following table:

Table 7

TEMP SELECT

SETTING

TEST

Interface Test*

Automatic Operations Test

Actuator and Switch Test

(PREFERRED SERVICE TEST)

Warm/Warm (WW)

Cold/Cold (CC)

Hot/Cold (HC)

Fig. 30

Flat of

Shaft

5.

Press and hold the START/PAUSE button while turning the CYCLE SELECT switch one step
clockwise.

6.

Release the START/PAUSE button.

NOTE: To terminate any diagnostic test and return to normal operation, unplug the washer power
cord from the power outlet for more than five seconds and then plug the power cord back into the
outlet.

*Interface Test

available on 4-temperature models

2.

Unplug the washer power cord from the household outlet for more than five seconds.

3.

Plug the washer back into the electrical power outlet.

4.

Set the CYCLE SELECT switch so the flat on the stem faces position 1 - Knob points to
the right.

(Fig. 30)

Cottons:

Normal

Cottons:

Heavy

Off

Permanent

Press

Delicate

Spin Only

Super

Wash

Soak

«
...
67
68
69
70
71
...
»

Содержание APARTMENT MAINTENANCE SERIES





































































































































Отзывы:

Нет отзывов

Похожие инструкции для APARTMENT MAINTENANCE SERIES

Washing machine

Бренд: Fagor Страницы: 12

Бренд: Zanussi Страницы: 32

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 19

Бренд: mabe Страницы: 32

Бренд: Alliance Laundry Systems Страницы: 38

Бренд: Majestic Appliances Страницы: 29

Бренд: ZANKER Страницы: 64

Бренд: GE Страницы: 72

Бренд: Kärcher Страницы: 52

Бренд: Ariston Страницы: 16

Бренд: SERVIS Страницы: 29

Бренд: Euromaid Страницы: 29

Бренд: Daewoo Страницы: 7

Бренд: Dexter Laundry Страницы: 6

Бренд: VYKING FORCE Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды