Welch Allyn ELI 150 Скачать руководство пользователя страница 22

Страница: 22 / 104

ELI 150

3-2



From the Set Time/Date screen, simultaneously press



(SHIFT) + ALT + C

. The first

configuration screen will appear. Notice the page indicator in the upper right hand corner on
each screen.

NOTES:

Use

Page (F4)

to toggle through the configuration pages.

Use

▲ (F1)

and

▼ (F2)

to move back and forth through each configuration option.

Use

► (F3)

to toggle through pre-programmed available settings per configuration field.

Use

Exit (F6)

to return to the Real-Time ECG View. Any changes you have made will be saved.

Use the

BACKSPACE



key to erase entry errors.

The following chart summarizes the configuration screens and the available options for each parameter.

Содержание ELI 150









































































































Результаты поиска

Содержание ELI 150

Отзывы:

Похожие инструкции для ELI 150

Бренды по названию

Популярные бренды

Welch Allyn ELI 150, Руководство по обслуживанию

Результаты поиска

Содержание ELI 150

Отзывы:

Похожие инструкции для ELI 150

Бренды по названию

Популярные бренды