Welch Allyn ELI 150 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 104

background image

ELI 150

7-3

GSM Modem Connectivity Option

The GSM Modem Connectivity option for the ELI 150 is soldered to the motherboard and is not field replaceable. If
there is a problem with the GSM Modem option the motherboard will require replacement.

It is important to note that there are two different versions of the GSM modems. The types are F1which is typically
for Europe (working in 900/1800 MHz bands) and F2 which is typically for North America (850/1900 MHz bands).
By looking at the motherboard or the GSM modem itself you will not be able to tell which GSM modem is installed.
If the motherboard of the ELI 150 must be replaced it must be replaced with the correct type of GSM mode. To
ensure that the correct options are installed please make sure that when ordering the board you specify the

UNIT

serial number

.

In order for the GSM modem to operate correctly a SIM card must be installed and the SIM card must have the Data
option activated. Mortara Instrument does not provide the SIM modules the can be obtained from the service
provider.

A replacement motherboard will require some assembly. The GSM modem will be soldered to the motherboard as
shown.

«
...
99
100
101
102
103
...
»

Содержание ELI 150









































































































Отзывы:

Нет отзывов

Похожие инструкции для ELI 150

Бренд: Keiser Страницы: 82

Бренд: Keiser Страницы: 4

Бренд: Warehouse-lighting Страницы: 3

Бренд: Eagle Group Страницы: 8

Бренд: E2S Страницы: 5

Бренд: PASCO Страницы: 30

Бренд: Garmin Страницы: 2

Бренд: Parker Страницы: 58

Бренд: Össur Страницы: 98

Flex Foot Cheetah

Бренд: Össur Страницы: 107

Бренд: Össur Страницы: 38

Бренд: Össur Страницы: 39

Bionic Symbionic Leg

Бренд: Össur Страницы: 2

Бренд: Össur Страницы: 67

Бренд: Össur Страницы: 17

Бренд: Kamar Страницы: 2

Бренд: Bayer HealthCare Страницы: 104

EDC2-1001-RGB-MWT

Бренд: Energizer Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды