manualshive.com logo in svg

Weil-McLain 550 MBH, Инструкция по установке и эксплуатации

Weil-McLain 550 MBH - надежный бойлер с производительностью 550 тыс. BTU в час. Установите и запустите его с легкостью, используя Руководство по установке и эксплуатации, доступное для загрузки бесплатно на manualshive.com. Профессиональный и надежный выбор для вашего дома или бизнеса.

Поделиться
Скачать
background image

Part number 550-100-168/0516

7

SlimFit

®

 Series 3 

COMMERCIAL

 

CONDENSING

 

GAS

-

FIRED

 

WATER

 

BOILER

 — 

Boiler Manual

Prepare boiler location

 

(continued)

Flooring and foundation

Flooring

1.  The SlimFit boiler is approved for installation on combustible 

flooring, but must never be installed on carpeting.

Do not install boiler on carpeting even if founda-
tion is used. Fire can result, causing severe personal 
injury, death or substantial property damage.

Foundation

1.  The boiler mounting surface must be level and suitable for 

the load.

2.  Provide a solid foundation pad, at least 2 inches above the 

floor, if any of the following is true:

s

floor can become flooded.

s

the floor is dirt, sand, gravel or other loose material.

s

the boiler mounting area is severely uneven or sloped.

3.  The minimum foundation size is:

s

48 inches wide x 20 inches deep.

4.  Foundation may be of wood, brick or concrete (minimum 2 

inches thick) construction.

5.  If flooding is possible, elevate boiler sufficiently to prevent 

water from reaching boiler.

Garage installation

Precautions

1.  Take the following special precautions when installing the 

boiler in a garage. If the boiler is located in a garage:

s

Mount the boiler at a height above the floor as specified 
in the National Fuel Gas Code, ANSI Z223.1 for U. S. 
installations, or CSA B149.1 and B149.2 for Canadian 
installations. 

s

Locate or protect the boiler so it cannot be damaged by 
a moving vehicle.

s

Ensure that the installation complies with all applicable 
codes.

Provide air openings to room

Air openings — General

Follow the National Fuel Gas Code (U. S.) or CSA B149.1 and 
B149.2 (Canada) and all applicable codes to size/verify size of the 
combustion/ventilation air openings into the space. See the vent-
ing instructions section of this manual for required air openings 
and sizing for either direct vent or direct exhaust installation.

Air openings — SlimFit boiler alone in boiler 
room 

1.  DIRECT VENT — 

For direct vent installations (air piped 

to boiler), no air ventilation openings into boiler room are 
needed if clearances around the SlimFit boiler are at least 
equal to the SERVICE clearances shown in Figure 1, page 6. 
For spaces that DO NOT supply the minimum service access 
clearances, see the direct vent venting instructions in this 
manual for required openings.

2.  DIRECT EXHAUST — 

For direct exhaust installations (com-

bustion air from inside), provide air openings as specified in 
the direct exhaust venting section of this manual.

Air openings — SlimFit boiler in same room 
with other gas or oil-fired appliances

1.  DIRECT VENT —

 

For direct vent installations (combustion 

air piped to boiler), size openings only on the basis of the 
other appliances in the space. No additional air opening 
free area is needed for the SlimFit boiler because it takes its 
combustion air from outside.  

  For direct vent installations, when the SlimFit boiler 

is located in the same room as other appliances, 
provide combustion air openings correctly sized 
for all appliances in the room except the SlimFit 
boiler.

 

Reinstall the boiler jacket front door after servicing. 
The boiler front door must be securely fastened to 
the boiler to prevent the boiler from drawing air 
from inside the boiler room. This is particularly 
important if the boiler is located in the same room 
as other appliances.

 

Failure to comply with the above warnings could 
result in severe personal injury, death or substantial 
property damage.

2.  DIRECT EXHAUST — 

For direct exhaust installations, com-

bustion air openings into the room must be sized to handle 
the SlimFit boiler and all other appliances. See the direct 
exhaust venting instructions in this manual for required 
openings.

  For direct exhaust installations, when the SlimFit 

boiler is located in the same room as other appli-
ances, provide combustion air openings correctly 
sized for all appliances, including the SlimFit boiler.

 

Failure to comply with the above warnings could 
result in severe personal injury, death or substantial 
property damage.

Содержание 550 MBH

































































































































Отзывы:

Нет отзывов

Похожие инструкции для 550 MBH

Immergas VICTRIX X12-242I Instruction And Warning Book preview
VICTRIX X12-242I
Бренд: Immergas Страницы: 40
Raypak MVB 1003 Installation & Operating Instructions Manual preview
MVB 1003
Бренд: Raypak Страницы: 213
Viessmann VITODENS 200-W B2HE 199 Operating Instructions Manual preview
VITODENS 200-W B2HE 199
Бренд: Viessmann Страницы: 48
TriangleTube prestige Control Supplement preview
prestige
Бренд: TriangleTube Страницы: 32
Viadrus HERCULES DUO Manual For Operation And Installation preview
HERCULES DUO
Бренд: Viadrus Страницы: 76
Immergas VICTRIX ZEUS SUPERIOR 32 2 ERP Instruction And Warning Book preview
VICTRIX ZEUS SUPERIOR 32 2 ERP
Бренд: Immergas Страницы: 48
Weil-McLain 383-500-350 Supplement Manual preview
383-500-350
Бренд: Weil-McLain Страницы: 13
Ferroli MODENA S HE Instructions For Use, Installation And Maintenance preview
MODENA S HE
Бренд: Ferroli Страницы: 36
Camus Hydronics DynaFlame Series Installation And Service Manual preview
DynaFlame Series
Бренд: Camus Hydronics Страницы: 92
Unical S 24 Manual preview
S 24
Бренд: Unical Страницы: 52
Unical IDEA AC 23 Installation And Servicing Manual preview
IDEA AC 23
Бренд: Unical Страницы: 72
Unical ALKON 115 EXT Installation And Servicing Manual preview
ALKON 115 EXT
Бренд: Unical Страницы: 80
Ariston CLAS HE EVO Installation And Servicing Instructions preview
CLAS HE EVO
Бренд: Ariston Страницы: 72
Market Forge Industries M24G Parts And Service Manual preview
M24G
Бренд: Market Forge Industries Страницы: 16
Baxi ROCA NORA 28 Operating, Cleaning And Maintenance Instructions For The User preview
ROCA NORA 28
Бренд: Baxi Страницы: 9
Sime BRAVA ONE OF ErP Installation And Maintenance Manual preview
BRAVA ONE OF ErP
Бренд: Sime Страницы: 128
Rinnai E110CRN Installation & Servicing Instructions Manual preview
E110CRN
Бренд: Rinnai Страницы: 96
Truma Boiler Manual preview
Boiler
Бренд: Truma Страницы: 94

Бренды по названию

Популярные бренды

Загрузить еще бренды