Watson-Marlow 630 U Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 186

background image

Pumphead type

Value

Pumphead

0x—40

620R

0x—41

620RE (Sanitary element)

0x—42

620RE4 (Sanitary element)

0x—43

620L (Continuous tubing)

0x—44

620L (double-Y element)

0x—45

620RE (Industrial element)

0x—46

620RE4 (Industrial element)

Note:

Numerical values cannot include a decimal point. To enter a speed, move the decimal point one

place to the right and enter an integer. To enter a tube size, move the decimal point two places to the
right and enter an integer. See examples below:

Speed (rpm)

Value

123.4

1234

Data examples

Set min/max speeds

The min/max speed parameters are used to set the minimum and maximum speed from the PROFIBUS
interface. The values are only used if the matching bit in the Control Word is enabled and they are not
zero. All values are 16 bit unsigned in 1/10th of RPM of the head speed.

Fail-safe

The fail-safe user parameter is used to set the correct course of action to take in the event of a PROFIBUS
communications failure. The fail-safe byte is configured as shown in the following table. If no bits are set
or an invalid bit pattern is set the default fail safe behaviour shall be to stop the pump.

Bit

Description

0x00

No fail safe action

0x01

Last demanded speed

0x02

Fail-safe speed

The fail-safe speed parameter is used to set the speed at which the pump should be driven is a PROFIBUS
communications error occurs and if bit 1 in the fail safe user parameter is set.

m-630un-en-08

43

«
...
41
42
43
44
45
...
»

Содержание 630 U



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 630 U

Бренд: RAASM Страницы: 72

Бренд: Garantia Страницы: 2

VeroLine-IPS 20

Бренд: Wilo Страницы: 42

Бренд: Gardena Страницы: 10

Бренд: Pfeiffer Vacuum Страницы: 46

Бренд: EBARA Страницы: 172

WEATHERMAKER 50TFQ008

Бренд: Carrier Страницы: 28

969-9365 Series

Бренд: Varian Страницы: 71

Бренд: OSO Страницы: 44

Бренд: York Страницы: 178

Бренд: salmson Страницы: 24

Бренд: Yardworks Страницы: 19

PE-2F-PW Series

Бренд: Little Giant Страницы: 2

Бренд: Waterhouse Страницы: 4

Бренд: VAKI Страницы: 9

Бренд: DAXOM Страницы: 20

Бренд: Peraqua Страницы: 60

Бренд: Pentair Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды