Watson-Marlow 630 U Скачать руководство пользователя страница 175

Страница: 175 / 186

31.3

CIP and SIP procedures

General instructions

Unlock the guard and disengage the rollers.

Close the guard and squeeze against the track until the latch clicks.

Observe a 1m safety area.

CIP

LoadSure tube elements and continuous tubing can be cleaned using CIP process.

Ensure that the tubing material is chemically compatible with the cleaning agent that is to be used.

If cleaning agents are spilled over the pumphead, wash down immediately.

Ensure that controlled waste pipe work is fitted to allow safe release of cleaning agent in the event of a

tube failure.

SIP

Only STA-PURE Series PCS tube elements can be used in steam-in-place sterilisation processes.

STA- PURE Series PCS tubing elements can be sterilised to 3A Class 2 and FDA minimum

recommended standard which is 121C (250F) at 1 bar (14.5 psi) saturated steam for 20 minutes.

Monitor the process continuously.

If a tube failure occurs, shut down the process. Do not touch the pumphead until a 20 minute

cooling down period has been observed.

Ensure a 20 minute acclimatisation period is observed before running the pump following SIP.

Ensure that controlled waste pipework is fitted to allow a safe release of steam in the event of a tube

failure.

Ensure a 1m safety zone is maintained around the pumphead during SIP cycles.

Ensure that the pumphead door is closed and locked before SIP cleaning
commences.

m-630un-en-08

175

Содержание 630 U



























































































































































































Результаты поиска

Содержание 630 U

Отзывы:

Похожие инструкции для 630 U

Бренды по названию

Популярные бренды

Watson-Marlow 630 U, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 630 U

Отзывы:

Похожие инструкции для 630 U

Бренды по названию

Популярные бренды