Watson-Marlow 630 U Скачать руководство пользователя страница 148

Страница: 148 / 186

Use the

∧

∨

keys to move the selection bar over the tube material to be used and press

SELECT

The PUMPHEAD MODEL screen allows the tube Lot Number to be recorded for future reference. Use the

∧

∨

keys to move the selection bar over

Tube lot number

and press

SELECT

Use the

∧

∨

keys to scroll through the available characters for each digit. The available characters are 0-9,

A-Z, and SPACE.

Press

NEXT

to move onto the next character, or

PREVIOUS

to move back to the last character.

Press

FINISH

to save the entry and return to the general settings menu.

Restore defaults

To restore the factory default settings select

Restore defaults

from the general settings menu.

There are two confirmation screens to ensure that this function is not carried out in error.

148

m-630un-en-08

Содержание 630 U



























































































































































































Результаты поиска

Содержание 630 U

Отзывы:

Похожие инструкции для 630 U

Бренды по названию

Популярные бренды

Watson-Marlow 630 U, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 630 U

Отзывы:

Похожие инструкции для 630 U

Бренды по названию

Популярные бренды