Watson-Marlow 630 U Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 186

background image

If hazardous fluids are to be pumped, safety procedures specific to the
particular fluid and application must be put in place to protect against injury
to persons.

This product does not comply with the ATEX directive and must not be used in
explosive atmospheres.

Ensure the chemicals to be pumped are compatible with the pumphead,
lubricant (where applicable), tubing, pipework and fittings to be used with
the pump. Please refer to the chemical compatibility guide which can be
found at:

www.wmftg.com/chemical

. If you need to use the pump with any

other chemical please contact Watson-Marlow to confirm compatibility.

If the Auto restart feature is enabled it may cause the pump to start as soon
as power is turned on.

Auto-restart only affects operation of manual mode, network mode and
memodose mode.

If Auto restart is enabled the "!" Symbol is shown on the screen to warn users
that the pump may operate without any manual intervention (pump resumes
with previous settings).

Do not use auto restart for more than 12 times in 24 hours. We recommend
remote control where a high number of starts is required.

If the pump is configured to network mode or analog mode it will respond to
remote commands at any time including immediately after power on. The "!"
Symbol is shown on the screen to warn users that the pump may operate
without any manual intervention (e.g. a remote setpoint could start the pump
with no key press required).

There are moving parts inside the pumphead. Before opening the tool-
unlockable guard or tool-unlockable track, ensure that the following safety
directions are followed:

1.

Ensure the pump is isolated from the mains power.

2.

Ensure that there is no pressure in the pipeline.

3.

If a tube failure has occurred, ensure that any fluid in the pumphead
has been allowed to drain to a suitable vessel, container or drain.

4.

Ensure that appropriate Personal Protective Equipment (PPE) is worn.

Primary operator protection from rotating parts of the pump is provided by
the pumphead safeguard. Note that safeguards differ, depending on the type
of pumphead. See the pumphead section of the manual.

12

m-630un-en-08

«
...
10
11
12
13
14
...
»

Содержание 630 U



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 630 U

Бренд: Samson Страницы: 26

Бренд: Macnaught Страницы: 12

Бренд: A.O. Smith Страницы: 2

Бренд: Danfoss Страницы: 34

Бренд: Danfoss Страницы: 52

Бренд: Wacker Neuson Страницы: 44

Бренд: Quincy Compressor Страницы: 122

Бренд: York Страницы: 84

Craftsman 390.269451

Бренд: Sears Страницы: 8

Бренд: Rheem Страницы: 28

Бренд: Rinnai Страницы: 2

Green Line D90 GL

Бренд: dosatron Страницы: 2

TV 301 Navigator 969-8918

Бренд: Varian Страницы: 55

Бренд: Ecoplus Страницы: 24

Бренд: Yardworks Страницы: 18

Бренд: Oase Страницы: 70

MAESTRO SMART 9HP

Бренд: Olimpia splendid Страницы: 52

Бренд: A.O. Smith Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды