Watson-Marlow 630 U Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 186

background image

Fundamental work with regard to lifting, transportation, installation,
starting-up, maintenance and repair should be performed by qualified
personnel only. The unit must be isolated from mains power while work is
being carried out. The motor must be secured against accidental start-up.

Some pumps weigh more than 18kg (the exact weight depends on the model
and pumphead - see on the pump). Lifting should be performed according to
standard Health and Safety guidelines. Finger recesses are built into the sides
of the lower shell for convenience in lifting; in addition, the pump can
conveniently be lifted by grasping the pumphead and (where fitted) the 'N'
module at the rear of the pump.

There is a user-replaceable fuse located at the rear of the pump. Some
country specific mains plugs contain an additional replaceable fuse. Fuses
must be replaced with parts with the same rating.

There are no user-serviceable fuses or parts inside this pump.

Note - the mains power supply cable is supplied hardwired into the pump and
is not customer replaceable.

Observe voltage selector switch setting for your region

IP66 pumps are supplied with a mains plug. The gland at the NEMA Module
end of the cable is IP66 rated. The mains plug at the opposite end of the
cable is NOT IP66 rated. It is the user's responsibility to ensure that the
connection to the mains supply is IP66 rated.

This pump must be used only for its intended purpose.

The pump must be accessible at all times to facilitate operation and maintenance. Access points must not
be obstructed or blocked. Do not fit any devices to the drive unit other than those tested and approved
by Watson-Marlow. Doing so could lead to injury to persons or damage to property for which no liability
can be accepted.

The pump's main plug is the disconnecting device (for isolating the motor drive from the mains supply
in an emergency). Do not position the pump so that it is difficult to disconnect the mains plug.

m-630un-en-08

11

«
...
9
10
11
12
13
...
»

Содержание 630 U



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 630 U

Бренд: RBI Страницы: 48

Бренд: Ulvac Страницы: 54

Бренд: Graco Страницы: 48

Бренд: Westinghouse Страницы: 12

jumbo floodfighter

Бренд: Davey Страницы: 8

Бренд: Masterbuilt Страницы: 4

Silencer AP Series

Бренд: HALE Страницы: 146

Бренд: Geotech Страницы: 32

Бренд: Gardena Страницы: 17

Бренд: Lampoassa Страницы: 62

Бренд: Zip Страницы: 24

Бренд: XtremepowerUS Страницы: 14

Gusher 30 Series

Бренд: Whale Страницы: 8

Pneumatic Oilpump 3:1

Бренд: Pressol Страницы: 28

Бренд: Fass Страницы: 13

Бренд: Bradford White Страницы: 2

VRV-WII RWEYQ-MY1 Series

Бренд: Daikin Страницы: 114

Бренд: Franklin Electric Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды