WAGO I/O-SYSTEM 750 Скачать руководство пользователя | Manualshive

Страница: 47 / 96

background image

WAGO-I/O-SYSTEM 750

Mounting

47

750-493 3-Phase Power Measurement Module

Manual

Version 1.2.0

Pos: 72 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Monti eren/M ontier en - Überschrift 1 @ 3\mod_1225446744750_21.docx @ 24900 @ 1 @ 1

6

Mounting

Pos: 73.1 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/M ontagerei henfolge @ 3\mod_1231770210031_21.docx @ 25992 @ 2 @ 1

6.1

Mounting Sequence

Fieldbus couplers/controllers and I/O modules of the WAGO-I/O-SYSTEM

750/753 are snapped directly on a carrier rail in accordance with the European

standard EN 50022 (DIN 35).

The reliable positioning and connection is made using a tongue and groove

system. Due to the automatic locking, the individual devices are securely seated

on the rail after installation.

Starting with the fieldbus coupler/controller, the I/O modules are mounted

adjacent to each other according to the project design. Errors in the design of the

node in terms of the potential groups (connection via the power contacts) are

recognized, as the I/O modules with power contacts (blade contacts) cannot be

linked to I/O modules with fewer power contacts.

Pos: 73.2 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sicherheits- und sonstig e Hinweise/Vorsicht/Vorsicht: Verl etzungsgefahr durch scharfkantige M esser kontakte! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 73.3 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sicherheits- und sonstig e Hinweise/Achtung/Achtung: Buskl emmen nur in vorgesehener R eihenfolg e stecken! @ 6\mod_1256194177073_21.docx @ 43429 @ @ 1

Insert I/O modules only from the proper direction!

All I/O modules feature grooves for power jumper contacts on the right side. For

some I/O modules, the grooves are closed on the top. Therefore, I/O modules

featuring a power jumper contact on the left side cannot be snapped from the top.

This mechanical coding helps to avoid configuration errors, which may destroy

the I/O modules. Therefore, insert I/O modules only from the right and from the

top.

Pos: 73.4 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sicherheits- und sonstig e Hinweise/Hinweis/Hi nweis: Busabschluss nicht vergessen! @ 6\mod_1256194225557_21.docx @ 43432 @ @ 1

Don't forget the bus end module!

Always plug a bus end module 750-600 onto the end of the fieldbus node! You

must always use a bus end module at all fieldbus nodes with WAGO-I/O-

SYSTEM 750 fieldbus couplers/controllers to guarantee proper data transfer.

Pos: 73.5 /Dokumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

«
...
45
46
47
48
49
...
»

Содержание I/O-SYSTEM 750

































































































Отзывы:

Нет отзывов

Похожие инструкции для I/O-SYSTEM 750

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 3

Бренд: Campbell Страницы: 22

Бренд: Campbell Страницы: 32

Бренд: Campbell Страницы: 40

CR3000 Micrologger

Бренд: Campbell Страницы: 12

Бренд: R.M. Young Страницы: 8

Бренд: Campbell Страницы: 21

SourceMeter 2400

Бренд: Keithley Страницы: 594

System SourceMeter 2601B

Бренд: Keithley Страницы: 864

Бренд: Labgear Страницы: 8

SourceMeter 2600B Series

Бренд: Keithley Страницы: 897

Бренд: Velleman Страницы: 96

Бренд: Daewoo Страницы: 17

Бренд: CA.MI Страницы: 68

Бренд: JRC Страницы: 308

Бренд: Chroma Страницы: 63

Ranger TDR VDV501-090

Бренд: Klein Tools Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды