manualshive.com logo in svg

WAGO I/O-SYSTEM 750, Руководство пользователя

Поделиться
Скачать
WAGO I/O-SYSTEM 750 Скачать руководство пользователя страница 41

WAGO-I/O-SYSTEM 750 

Function Description 

41 

750-493 3-Phase Power Measurement Module 

 

 

Manual 

 

Version 1.2.0  

 

Measured value 

50.1 Hz 

59.9 Hz 

cos phi 

750-493 

750-493/000-001 

Process value 

0xFFB2  (-78) 

0x0059  (89) 

Scaling factor PI 

0.01 / LSB 

0.01 / LSB 

Equation 

Measured value = Process value x Scaling factor PI

 

Measured value 

-0.78 

0.89 

 

When calculating current-dependent values, the 

current transformer ratio 

(CTR)

 must be taken into account when using a current transformer. 

 

 

 

Current transformers 

Current transformers are available on the market in different designs. On the 

primary side, currents of 20 A, 25 A, 30 A, 35 A, 40 A, 45 A, 50 A, 75 A, 100 A 

… 5000 A are supported, on the secondary side 1 A or 5 A. 

For example, transformation ratios of 45:1 A (750-493) or 200:5 A (750-493/000-

001) are possible. Thus, the corresponding current transformer ratios (CTR) are 

1:45 and 1:40. 

The I/O module allows you to set 

user scaling

 using WAGO-I/O-

CHECK

 or via 

Register 32, bit 0. If the bit is set to 0, user scaling is disabled (off) and the 

transformation ratio of the current is 1:1. 

If the bit is set to 1, user scaling is enabled (on) and the transformation ratio is 

already taken into account in the I/O module. The transformation ratio is set using 

WAGO-I/O-

CHECK

 or in Register 37. The 

divisor of the CTR (D-CTR)

 is set in 

the register, i.e. according to the examples above: 

•

 

1A variants: 

CTR = 1:45,  D-CTR = 45  => Register 37 

•

 

5A variants: 

CTR = 1:40,  D-CTR = 40  => Register 37 

In the I/O module, the RMS values of the currents are represented in the process 

image according to the table "Measured values in the process image (PI)" above 

as UInt16 with the following scaling: 

•

 

1A variants: 

0.001 A / LSB 

•

 

5A variants: 

0.005 A / LSB 

Only the following maximum currents can be represented in the process image 

and thus only the corresponding maximum CRT values can be supported: 

1A variants: 

 

 

0 ... 65535 at 1 mA/LSB   =>   0.000 ... 65.535 A 

and thus: 

D-CTR max. = 50,  transformation ratios max. = 50:1 A 

5A variants:  

 

0 ... 65535 at 5 mA/LSB   =>   0.000 ... 327.675 A 

and thus: 

 D-CTR max. = 50,  transformation ratios max. = 250:5 A 

Содержание I/O-SYSTEM 750

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды