WAGO I/O-SYSTEM 750 страница 35 Скачать руководство пользователя

Страница: 35 / 96

WAGO-I/O-SYSTEM 750

Function Description

750-493 3-Phase Power Measurement Module

Manual

Version 1.2.0

Pos: 69 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/F unktionsbeschr eibungF unktionsbeschr eibung - Überschrift 1 @ 4\mod_1239025975389_21.docx @ 30003 @ 1 @ 1

Function Description

Pos: 70 /Serie 750 ( WAGO-I/O-SYST EM)/F unktionsbeschr eibung/Funkti onsbeschrei bung 750-0493 @ 14\mod_1361260872587_21.docx @ 112240 @ 2222 @ 1

0493 @ 14\mod_1361260872587_21.docx @ 112240 @ 2222 @ 4

5.1

Measuring Principle

The 3-phase power measurement module operates using 6 analog/digital

converters for acquiring the current and voltage levels in all three phases. The 3

phases are connected to the current measuring channels of the I/O module in

"single-ended" measurement topology. Each of the 6 measurement inputs is

scanned at a frequency of 8 kHz. The input filters on the measuring channels have

a limit frequency of 7.2 kHz. The analog measured values are quantized with 24

bits and further processed digitally.

Acquisition and processing of the measured values of all three phases is

performed simultaneously in the very same way.

5.2

Measured Values and Measured Value Calculation

The 3-phase power measurement module makes the following

AC measured

values

available per phase (Lx = L1, L2 or L3):

Voltage:

•

RMS value voltage Lx – N

•

Maximum RMS value voltage Lx – N

•

Minimum RMS value voltage Lx – N

Current:

•

RMS value current Lx

•

Maximum RMS value current Lx

•

Minimum RMS value current Lx

Power:

•

Active power Lx

•

Maximum value active power Lx

•

Minimum value active power Lx

Energy:

•

Active energy Lx

Frequency:

•

Supply network frequency Lx

Power factor:

•

cos phi Lx

Limit value:

•

Undervoltage Lx: Threshold value undershot

Alternatively, the following

DC measured values

are available if DC

measurement has been activated in the I/O module. See section "Commissioning"

> "Configuration with WAGO-I/O-

CHECK

Voltage:

•

DC voltage Lx – N

Current:

•

DC current Lx

Power:

•

Power (DC current) Lx

Содержание I/O-SYSTEM 750

































































































Результаты поиска

Содержание I/O-SYSTEM 750

Отзывы:

Похожие инструкции для I/O-SYSTEM 750

Бренды по названию

Популярные бренды

WAGO I/O-SYSTEM 750, Руководство пользователя

Результаты поиска

Содержание I/O-SYSTEM 750

Отзывы:

Похожие инструкции для I/O-SYSTEM 750

Бренды по названию

Популярные бренды