WAGO 761-210 Скачать руководство пользователя страница 31

Страница: 31 / 84

WAGO-TO-PASS® 761

Mounting

761-210 Telecontrol Module Compact

Manual

Version 2.0.0

Mounting

IP20 degree of protection

The protection class of the

TO-PASS

telecontrol module is IP 20. For this reason,

WAGO Kontakttechnik GmbH & Co. KG recommends mounting in a housing or
in a switching cabinet.

Ambient temperature -20 °C to +70 °C

The

TO-PASS

telecontrol module is designed for an ambient temperature of -20

°C to +70 °C.
In the event of higher or lower temperatures, proper cooling or heating
arrangements must be provided.
Please contact WAGO Kontakttechnik GmbH & Co. K.G. for assistance.

The

TO-PASS

telecontrol module is designed to mount on a DIN 35 carrier rail.

4.1

Mounting the TO-PASS

telecontrol module to the

DIN rail

Figure 10: Mounting the

TO-PASS

telecontrol module to the DIN rail

Place the

TO-PASS

telecontrol module on the DIN rail from above.

Press the undersurface against the lower DIN rail edge until the

TO-PASS

telecontrol module locks into place.

Содержание 761-210





















































































Результаты поиска

Содержание 761-210

Отзывы:

Похожие инструкции для 761-210

Бренды по названию

Популярные бренды

WAGO 761-210, Руководство пользователя

Результаты поиска

Содержание 761-210

Отзывы:

Похожие инструкции для 761-210

Бренды по названию

Популярные бренды