WAGO 761-210 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 84

background image

14

Important Notes

WAGO-TO-PASS® 761

761-210 Telecontrol Module Compact

Manual

Version 2.0.0

Protect the components against materials having seeping and insulating
properties!

The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.

Cleaning only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.

Avoid electrostatic discharge!

The devices are equipped with electronic components that you may destroy by
electrostatic discharge when you touch. Pay attention while handling the devices
to good grounding of the environment (persons, job and packing).

«
...
12
13
14
15
16
...
»

Содержание 761-210





















































































Отзывы:

Нет отзывов

Похожие инструкции для 761-210

Бренд: VAT Страницы: 29

Бренд: Balboa Instruments Страницы: 19

C-NaviGator III

Бренд: C-Nav Страницы: 20

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 20

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

Бренд: Febco Страницы: 12

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Oceanic Страницы: 11

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: Rabe Страницы: 61

Бренд: Racal Instruments Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды