WAGO 761-210 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 84

background image

56

Commissioning

WAGO-TO-PASS® 761

761-210 Telecontrol Module Compact

Manual

Version 2.0.0

6.11

Configuring Error Detectors

The

TO-PASS

®

telecontrol module can transmit error messages to a maximum of

four recipients. The recipients are informed either directly one after another or (if
configured) after expiration of the time delay for acknowledgment. The message
is sent by the

TO-PASS

®

telecontrol module as an SMS; however, it can also be

sent as an e-mail, fax or voice mail. In addition, the error messages can also be
transmitted to a Web portal.

Device-dependent Function

Devices with GPRS functionality (device identifier "Web") are required to
transmit error messages to a Web portal.

Note the calculation packet size!

Please note the information given on calculation packet size in the Section
"Important Information - Rounding of Blocks for GPRS Links."

6.11.1

Alarm Messages for Digital Inputs

If on or off states of digital inputs are to be sent as error messages, select the
desired recipient for the respective input statuses using buttons

[1]

...

[4].

Click

the

[Internet]

button to also transmit the message to a Web portal.

In addition, you can also specify the analog values that are to be transmitted along
with the error message.

6.11.2

Limit Messages for Counter Inputs

If violations of upper/lower counter limits are to be sent as error messages,
activate the respective counter value and select the desired recipient using buttons

[1]

...

[4]

.

Click the

[Internet]

button to also transmit the message to a Web portal.

You can also specify the analog values that are to be transmitted along with the
error message.

«
...
54
55
56
57
58
...
»

Содержание 761-210





















































































Отзывы:

Нет отзывов

Похожие инструкции для 761-210

Бренд: Eaton Страницы: 166

Бренд: Garmin Страницы: 12

Бренд: Ohsung Electronics Страницы: 18

Бренд: Bartlett Страницы: 5

Бренд: Ultratec Страницы: 33

Бренд: Yamaha Страницы: 92

FEBCO 860 Small Series

Бренд: Watts Страницы: 12

Бренд: Bardiani Valvole Страницы: 54

Бренд: Parker Страницы: 478

TruPortal TP-ADD-1DIP

Бренд: Interlogix Страницы: 9

Бренд: Dejero Страницы: 24

Бренд: WINDY NATION Страницы: 16

Бренд: Kaba Mauer Страницы: 10

Бренд: HEIDENHAIN Страницы: 257

Бренд: Simpnic Страницы: 16

Бренд: MERCATOR Страницы: 4

Бренд: W&T Страницы: 217

Бренд: Jetter Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды