WAGO 761-210 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 84

background image

WAGO-TO-PASS® 761

Important Notes

13

761-210 Telecontrol Module Compact

Manual

Version 2.0.0

Please note the following information about FCC Part 15!

FCC Part 15.19

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that
may cause undesired operation.

FCC Part 15.21

Modifications not expressly approved by this company could void the user's
authority to operate the equipment..

Installation by qualified electrician only

The

TO-PASS

®

telecontrol module must be operated with Antenna 758-0963.

The antenna gain main not exceed 3 dBi.
Only qualified staff can install and maintain the

TO-PASS

®

remote module and its

antenna. The transmitted must be off when working on or nearer to the antenna
than specified below.

HF-Exposition

The external antenna operated with the

TO-PASS

®

remote module must be at least

20 cm away from people. The antenna may not be positioned, so that it works in
conjunction with any other antenna or transmitter.

Hot surface!

The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.

«
...
11
12
13
14
15
...
»

Содержание 761-210





















































































Отзывы:

Нет отзывов

Похожие инструкции для 761-210

Бренд: Daikin Страницы: 2

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 21

Бренд: Daikin Страницы: 20

Бренд: Eaton Страницы: 28

Бренд: Parallel Страницы: 16

Бренд: V2 Страницы: 46

Бренд: LAS Страницы: 6

Бренд: National Instruments Страницы: 72

Бренд: National Instruments Страницы: 41

MAGNUM ALERT 3000 FIRE ALARM

Бренд: NAPCO Страницы: 2

Бренд: Miller-Leaman Страницы: 18

Бренд: FUTABA Страницы: 8

Бренд: EOS Страницы: 7

Бренд: Daikin Страницы: 32

R1000 series E20

Бренд: Roland Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды