WAGO 761-210 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 84

background image

60

Commissioning

WAGO-TO-PASS® 761

761-210 Telecontrol Module Compact

Manual

Version 2.0.0

Table 27: Configuring the transmission repeat times

SMS Settings

SMS interval

Here, enter the cycle time in minutes to define the intervals
that the

TO-PASS

®

telecontrol module is to send data to the

addresses defined under

Address

.

SMS content is specific to devices and firmware used and is
described in the Section "Operation – Remote Polling by
SMS".
The cyclic SMS can, for example, be used for operational
supervision.

Address

Use this button to select the addresses to which the message
is to be transmitted in defined cycles.

Limited SMS
transmission

Check this box to limit the SMS interval to certain days of
the week and to certain times of day.
Time adjustment must be performed for limited SMS
transmission to check the day of the week and the active
time.
The first SMS is transmitted when the starting value for the
active time on an active day is reached. The SMS is also
transmitted when a cycle time of "0" has been defined. The
transmission cycle is started when the cycle time is situated
within the active time.
This function is available starting with Firmware Version FW
2.33.

Active time

In these fields you can select the starting and end points for
the active time in "hh:mm".
The starting point must be before the end time. A selection
not in line with these requirements will be adapted
automatically.
These selection fields are active only when the box

Limited

SMS transmission

has been checked.

Active days

Check these boxes to mark the active days for SMS
transmission.
These boxes are active only when the

Limited SMS

transmission

box has been checked.

«
...
58
59
60
61
62
...
»

Содержание 761-210





















































































Отзывы:

Нет отзывов

Похожие инструкции для 761-210

Бренд: Abus Страницы: 12

Бренд: Yardney Страницы: 8

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

Бренд: Osram Страницы: 3

Бренд: mikroElektronika Страницы: 3

Бренд: Window Master Страницы: 7

Бренд: Monster Central Страницы: 13

Бренд: Rain Bird Страницы: 18

Бренд: Conductrix Wampfler Страницы: 23

Бренд: Carel Страницы: 2

Бренд: Timotion Страницы: 9

Бренд: FMS Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды