WAGO 761-210 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 84

background image

WAGO-TO-PASS® 761

Commissioning

59

761-210 Telecontrol Module Compact

Manual

Version 2.0.0

Table 27: Configuring the transmission repeat times

Web settings

Web interval

In this field enter the cycle time in minutes to define the
intervals that the

TO-PASS

®

telecontrol module is to send

data to the Internet.
Enter a "0" to deactivate cyclical data transmission.
The maximum value that you can enter here is 9999 minutes,
which corresponds to around one transmission per week.

Device-dependent function

The function is only available for devices with
GPRS functionality (device identification "Web").

Note the calculation packet size!

Please note the information given on calculation
packet size in the Section "Important Information -
Rounding of Blocks for GPRS Links."

Switched interval

Check this box to have the transmission interval switched as
a function of the status of a digital input between Web
interval and switching interval.
This function is available starting with Firmware Version FW
2.33.

Switching input

In this field, select a digital input to be used for switching of
the transmission interval between Web interval (Off status of
the input) and the switching interval (On status of the input).
When the status of the switching input changes, the initial
transmission is triggered, followed by transmission at the
cycle time defined in the field

Switching interval

.

This selection field is active only when the

Switched

interval

box is checked.

Counter inputs may not be defined as switching
inputs

Counter inputs may not be used as switching
inputs, as no status changes are evaluated for these
inputs.

Switching interval In this field enter the cycle time in minutes to define the

intervals that the

TO-PASS

®

telecontrol module is to send

data to the Internet.
Enter a "0" to deactivate cyclical data transmission.
The maximum value that you can enter here is also 9999
minutes.

Web outputs

Use these buttons to select the inputs whose default setpoints
can be modified via responses from the Web portal.
This function is available starting with Firmware Version FW
2.33.

«
...
57
58
59
60
61
...
»

Содержание 761-210





















































































Отзывы:

Нет отзывов

Похожие инструкции для 761-210

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Fantech Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Maestra Страницы: 22

Бренд: GBD Страницы: 60

Бренд: Hunter Страницы: 2

Бренд: Tektronix Страницы: 112

Бренд: IN-COMMAND Страницы: 47

Бренд: SYCLOPE Страницы: 60

CIATControl OPC Server

Бренд: CIAT Страницы: 32

Бренд: Danfoss Страницы: 8

Infi 90 IMAOM01

Бренд: Bailey Страницы: 44

Бренд: Fibocom Страницы: 79

Бренд: oventrop Страницы: 40

Бренд: Sentiotec Страницы: 45

Бренд: LCT Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды