WAGO 750-482/000-001 Скачать руководство пользователя

Страница: 44 / 92

44 Connect Devices

WAGO I/O System 750

750-482/000-001 2AI 4-20mA HART NAMUR NE43

Manual

Version 1.0.2

Connect Devices

6.1

Connecting a Conductor to the CAGE CLAMP

The WAGO CAGE CLAMP

connection is appropriate for solid, stranded and

finely stranded conductors.

Only connect one conductor to each CAGE CLAMP

Only one conductor may be connected to each CAGE CLAMP

Do not connect more than one conductor at one single connection!

If more than one conductor must be routed to one connection, these must be

connected in an up-circuit wiring assembly, for example using WAGO feed-

through terminals.

For opening the CAGE CLAMP

insert the actuating tool into the opening

above the connection.

Insert the conductor into the corresponding connection opening.

For closing the CAGE CLAMP

simply remove the tool. The conductor is

now clamped firmly in place.

Figure 10: Connecting a Conductor to a CAGE CLAMP

Avoid short circuit

A short circuit between the "HART+" connectors and ground can destroy the

module. Therefore, make sure that no grounded part of the field device housing

comes into contact with the "HART+" connector, for example, during installation.

Содержание 750-482/000-001





























































































Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды

WAGO 750-482/000-001, Руководство пользователя

Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды