WAGO 750-482/000-001 Скачать руководство пользователя

Страница: 61 / 92

WAGO I/O System 750

Commissioning 61

750-482/000-001 2AI 4-20mA HART NAMUR NE43

Manual

Version 1.0.2

9.1.2

Startup on the 75x-xxx via PLC Library

This section describes the most important steps for commissioning the HART I/O

module on a 75x-xxx fieldbus coupler/controller using the HART library.

In addition to the fully installed and connected hardware of the fieldbus node with

fieldbus coupler/controller interface, it is necessary to install the following

software before carrying out the operation described.

Table 38: Required Software for Startup on 75x-xxx via PLC Library

No. Software name

Description

Item number

1 WAGO-I/O-

CHECK

(optional)

Commissioning tool for the

WAGO-I/O-SYSTEM 750

759-302

2 WAGO-I/O-

PRO

CAA

Programming tool IEC

61131-3; CAA Version

2.3; CODESYS

Automation Alliance

759-333

3 WagoLibHART_0x.lib

WAGO-I/O-

PRO

Libraries Download:

www.wago.com

When the HART I/O module is delivered, the default operating mode (2 AI + 6-

byte mailbox) is preset.

If the operating mode has already been changed, e.g., the module has been

used in a PROFIBUS system, the operating mode must be parameterized again

for the default setting

Launch WAGO-I/O-

CHECK

and set the operating mode to “2 AI + 6-byte

mailbox”.

Proceed as described in the Section “Operating Modes” > … > “Setting via

WAGO-I/O-

CHECK

”.

WAGO-I/O-

CHECK

up to Version 3.17.1.17:

Setting Limitations for PROFIBUS Operating Modes

For the PROFIBUS operating modes “1, 2, 3 or 4 HART variable(s) per channel”,

switching via WAGO-I/O-

CHECK

and operation on a fieldbus coupler other than

a PROFIBUS fieldbus coupler (750-333) or controller (750-833) is not currently

possible. A HART I/O module set up for HARD dynamic variables using GSD

files can therefore currently only be operated with a PROFIBUS fieldbus coupler

(750-333) or controller (750-833).

It is then possible to restore the default state of the HART I/O module using

WAGO-I/O-

CHECK

and the PROFIBUS fieldbus coupler (750 333) or controller

(750-833). Make sure that the PROFIBUS fieldbus coupler (750-333) or

controller (750-833) is not parameterized using GSD files.

Launch WAGO-I/O-PRO CAA, select the

Resources

tab and double-click

in the tree structure on

Library Manager

to open the respective dialog.

Integrate the “WagoLibHART_0x.lib” library for your “IEC 61131-3” project.

Содержание 750-482/000-001





























































































Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды

WAGO 750-482/000-001, Руководство пользователя

Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды