WAGO 750-482/000-001 Скачать руководство пользователя

Страница: 63 / 92

WAGO I/O System 750

Commissioning 63

750-482/000-001 2AI 4-20mA HART NAMUR NE43

Manual

Version 1.0.2

Consider the maximum number of modules!

Because of the process data capacity of the HART I/O module, please be sure to

take into account the corresponding maximum number of modules that can be

connected when using a WAGO PROFIBUS DP/V1 Coupler 750-333 or

Controller 750-833. You can find this number in the table “Compatibility List”.

With PROFIBUS, it is possible to evaluate and process further information in

addition to the actual measured signal, which is output in the main variables. This

additional information is then output accordingly by means of the HART dynamic

variables.

Some HART field devices (sensors) provide such additional information, an

example being a pressure transducer, which depending on the type of

measurement also provides such data as the sensor or electronics temperature

in the dynamic variables along with the actual process value (e.g., pressure, flow

or level).

Additional Information for the Application

You can read a detailed description with a clear application example for the

PROFIBUS connection using HART dynamic variables in a superimposed

CODESYS or Siemens controller in the appropriate application note, which

describes the use of HART I/O modules on the PROFIBUS DP/V1 coupler. You

will find this application note on the WAGO website at:

www.wago.com

→ Support → Additional documentation and information on

automation products → Application Notes

Содержание 750-482/000-001





























































































Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды

WAGO 750-482/000-001, Руководство пользователя

Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды