WAGO 750-482/000-001 Скачать руководство пользователя страница 66

Страница: 66 / 92

66 Commissioning

WAGO I/O System 750

750-482/000-001 2AI 4-20mA HART NAMUR NE43

Manual

Version 1.0.2

Now expand the device catalog and using “Drag&Drop” add the remaining

I/O modules that you have plugged into your fieldbus node on the

coupler/controller.

In doing so, you will find a total of five entries for the HART I/O Module

corresponding to the operating modes.

You will find a description of the different entries with a list of all the

associated parameters in the section “Operating Modes” > … > “Setting Up

via GSD”.

Figure 19: HW Config in STEP7

10. Select the entry corresponding to the required operating mode and

incorporate this into your configuration.

11. Double-clicking on a module in the configuration tree structure will open a

module-specific parameterizing dialog in which you can set the parameters

for the PROFIBUS Coupler 750-333 or Controller 750-833, the HART I/O

module and other parameterizable I/O modules.

Set the required parameter data.

12. Next save and translate the network configuration and transfer the new

project to the PLC.

9.3

FDT/DTM with the PROFIBUS DP/V1 750-333,

750-833

In the operating mode “2AI + acyclic PROFIBUS services”, when the HART I/O

module is connected to a PROFIBUS Coupler 750-333 or Controller 750-833, it is

also possible to carry out HART communication by means of the FDT/DTM frame

application “

WAGOframe

”. The device driver “Profibus/HARTGatewayDTM 759-

360” is available for using the FDT/DTM frame application “

WAGOframe

”, by

means of which FDT tool routing from the PROFIBUS DP/V coupler/controller to

the DTM of the connected HART device is possible. In this case, HART

communication takes place by means of the acyclic PROFIBUS services, which

are processed by a 12-byte mailbox.

Содержание 750-482/000-001





























































































Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды

WAGO 750-482/000-001, Руководство пользователя

Результаты поиска

Содержание 750-482/000-001

Отзывы:

Похожие инструкции для 750-482/000-001

Бренды по названию

Популярные бренды